Mazda 2014 CX-9 User Manual Download Page 460 | Manualshive

Page: 460 / 604

background image

Black plate (460,1)

WARNING

Place the specialized temporary spare
tire in the spare tire carrier correctly:

Placing the specialized temporary
spare tire in the spare tire carrier
wrong side up or using any tire other
than the small temporary spare tire
designed for use with this vehicle is
dangerous. It will result in poor
attachment and insufficient ground
clearance in the spare tire carrier and
the danger of the tire falling off. This
could result in someone being badly
injured or even killed.

Always tighten the spare tire carrier
bolt completely tight and make sure
the spare tire is locked in the highest
position:

A loose spare tire carrier bolt is
dangerous. The cable could be cut
causing the spare tire to fall off. This
could result in someone being
seriously injured or even killed. Use a
lug wrench to tighten the carrier bolt
and make sure to tighten it until a
click sound is heard.

CAUTION

If you hear rattling from the spare
tire carrier while the vehicle is
moving, the spare tire carrier cable
may be cut.
Have it repaired at an Authorized
Mazda Dealer as soon as possible.

Changing a Flat Tire

NOTE

If the following occurs while driving, it could
indicate a flat tire.

l

Steering becomes difficult.

l

The vehicle begins to vibrate excessively.

l

The vehicle pulls in one direction.

If you have a flat tire, drive slowly to a
level spot that is well off the road and out
of the way of traffic to change the tire.
Stopping in traffic or on the shoulder of a
busy road is dangerous.

WARNING

Be sure to follow the directions for
changing a tire:

Changing a tire is dangerous if not
done properly. The vehicle can slip off
the jack and seriously injure
someone.
No person should place any portion
of their body under a vehicle that is
supported by a jack.

Never allow anyone inside a vehicle
supported by a jack:

Allowing someone to remain in a
vehicle supported by a jack is
dangerous. The occupant could cause
the vehicle to fall resulting in serious
injury.

CAUTION

(With Tire Pressure Monitoring
System)

The wheels equipped on your Mazda
are specially designed for installation
of the tire pressure sensors. Do not
use non-genuine wheels, otherwise it
may not be possible to install the tire
pressure sensors.

7-8

In Case of an Emergency

Flat Tire

CX-9_8DU1-EA-14H_Edition1 Page460
Thursday, June 5 2014 4:20 PM

Form No.8DU1-EA-14H

«
...
458
459
460
461
462
...
»

Summary of Contents for 2014 CX-9





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 CX-9

MARTEN-FREE CAR

Brand: Gardigo Pages: 36

PRIME DESIGN VRI3-E-PM11

Brand: Safe Fleet Pages: 12

Brand: Toyota Pages: 56

Brand: Axxess Pages: 8

Brand: Ford Pages: 38

Brand: Thule Pages: 8

Brand: CITROËN Pages: 301

Brand: tams elektronik Pages: 19

Brand: Blue Ox Pages: 5

Brand: Ranger design Pages: 22

Brand: Brainz Pages: 2

Brand: Reese Pages: 21

Brand: Crux Pages: 10

Brand: Yakima Pages: 9

Auto Security AA-9103N

Brand: Audiovox Pages: 1

IONIQ HYBRID 2019

Brand: Hyundai Pages: 16

GRAND CHEROKEE 4xe 2023

Brand: Jeep Pages: 440

Brand: Genesis Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands