Mazda 2013 CX-5 Workshop Manual Download Page 37

Page: 37 / 223

DTC C0044:01/C0044:28/C0044:54/C0044:64 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2888500.html[1/7/13 9:29:19 AM]

< Previous

Next >

2013 - CX-5 - Brakes

DTC C0044:01/C0044:28/C0044:54/C0044:64 [DYNAMIC STABILITY CONTROL (DSC)]

DTCC0044:01, C0044:28,

C0044:54, C0044:64

Brake fluid pressure sensor

DETECTION

CONDITION

C0044:01

The voltage value from the brake fluid pressure sensor is

not within specification.

C0044:28, C0044:64

The pressure from the brake fluid pressure sensor is not

within specification.

C0044:54

The brake fluid pressure sensor detects the initialization

procedure has not been perform.

FAIL-SAFE

FUNCTION

C0044:01

Illuminates the TCS/DSC indicator light.

Tire pressure monitoring system warning light illuminates

after flashes. (Not illuminated/flashed depending on

malfunction content.)

Inhibits the TCS

, DSC

, roll over mitigation (ROM)

, brake

assist control, hill launch assist (HLA)

, and TPMS

controls.

C0044:28, C0044:64

Illuminates the TCS/DSC indicator light.

Tire pressure monitoring system warning light illuminates

after flashes.

Inhibits the TCS, DSC, roll over mitigation (ROM), brake

assist control, hill launch assist (HLA), and TPMS controls.

C0044:54

Illuminates the TCS/DSC indicator light.

Tire pressure monitoring system warning light illuminates

after flashes. (Not illuminated/flashed depending on

malfunction content.)

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands