Mazda 2013 CX-5 Workshop Manual Download Page 34

Page: 34 / 223

DTC C0040:64 [DYNAMIC STABILITY CONTROL (DSC)]

http://am.mazdaserviceinfo.com/emazda/dealersystem/service/esi/en_us/SM/2013/CX5/mv/books/mvw04/html/id0402b2877500.html[1/7/13 9:29:15 AM]

< Previous

Next >

2013 - CX-5 - Brakes

DTC C0040:64 [DYNAMIC STABILITY CONTROL (DSC)]

DTC

C0040:64

Brake switch

DETECTION

CONDITION

Brake switch ON signal is input for

6 min or more

when driving at a vehicle speed of

km/h {12 mph} or more

A brake switch ON signal is not input when the brake fluid pressure sensor signal reaches the

specified value.

FAIL-SAFE

FUNCTION

Illuminates the TCS/DSC indicator light.

Tire pressure monitoring system warning light illuminates after flashes.

Inhibits the brake assist control, hill launch assist (HLA), and TPMS controls.

POSSIBLE CAUSE

Open or short circuit in wiring harness between the brake switch and PCM terminal 2G

Brake switch malfunction

Poor connection at connectors (female terminal)

Summary of Contents for 2013 CX-5
































































































































































































































Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands

Mazda 2013 CX-5, Workshop Manual

Search results

Summary of Contents for 2013 CX-5

Reviews:

Related manuals for 2013 CX-5

Brands by name

Popular brands