Mazda 2007 CX-7 Bodyshop Manual Download Page 16

Page: 16 / 138

GENERAL INFORMATION

00-00–14

ANTICORROSION, SOUND INSULATION, AND VIBRATION INSULATION

id000000600600

Body Sealing

•

Apply body sealer where necessary.

•

For locations where application of body sealer is difficult after installation, apply it before installation.

Application of Undercoating

•

Apply an undercoat to the required location of the body.

Application of Rust Inhibitor

•

Apply rust inhibitor (wax, oil, etc.) to the back of the welded areas.

Application of Floor Silencer

•

Apply floor silencer by heating with an infrared ray lamp.

End Of Sie

acxuub00000059

acxuub00000060

acxuub00000061

acxuub00000062

3419-1U-06C(00-00).fm 14 ページ２００６年３月２２日　水曜日　午後４時１４分

Summary of Contents for 2007 CX-7











































































































































Search results

Summary of Contents for 2007 CX-7

Reviews:

Related manuals for 2007 CX-7

Brands by name

Popular brands

Mazda 2007 CX-7, Bodyshop Manual

Search results

Summary of Contents for 2007 CX-7

Reviews:

Related manuals for 2007 CX-7

Brands by name

Popular brands