Maytag Performance MGDE300VF1, Use & Care Manual

Page: 7 / 16

Timed Cycles
Load Type
Temperature Time
(Minutes)
TIMED DRY
Heavyweight items, bulky items,
bedspreads, work clothes
High 40
TOUCHUP (on some models)
Help to smooth out wrinkles
Regular 15
QUICK DRY
Small loads
High 25
7
Manual Preset Cycle Settings
NOTES:
■ A light next to each feature will glow yellow when the feature is
selected. The light will not glow when the selection is
unavailable with the cycle or option combinations selected.
■ While a Timed Cycle is running, you can change the settings for
Time, Temperature, the WRINKLE PREVENT feature and the
cycle signals. Press the START-PAUSE button once to stop the
dryer, allowing you to select another cycle.
■ Press the TIME ADJUST up or down buttons until the desired
drying time is displayed. Press TIME ADJUST, and the time will
change by 1-minute intervals. Press and hold TIME ADJUST, and
the time will change by 5-minute intervals. The initial time
displayed is the actual drying time.
■ Temperature settings can be changed only with Timed Cycles.
Steam Cycles
In these cycles, a small amount of water is sprayed into the dryer
drum after several minutes of tumbling with heat. The dryer will
continue to tumble at Regular heat for the duration of the cycle. The
Steam cycles include Rapid Refresh and Custom Refresh. The heat
setting and cycle time are not adjustable for the Rapid Refresh cycle,
but can be adjusted for the Custom Refresh cycle.
NOTE: Results may vary depending on fabric. 100% cotton garments
with wrinkle-free finish may yield better results than those without.
Use of a fabric softener sheet is not recommended with steam cycles
as it may cause temporary staining on the clothes.
Steam Preset Cycle Settings
Timed Cycles
Load Type
Default
Temperature*
Default Time
(Minutes)*
RAPID REFRESH
Helps to smooth out
wrinkles and reduce odors
from loads consisting of one
to four dry items.
Regular 15
CUSTOM REFRESH
Helps to smooth out
wrinkles in loads left in the
dryer for an extended
period.
Regular 20
*NOTE: The Custom Refresh cycle has a minimum dry time of
15 minutes and a maximum dry time of 40 minutes. Only the
Regular and High temperature settings can be used for the Custom
Refresh cycle.
NOTE: During the Custom Refresh Cycle, you can change the
settings for Time, Temperature, the Wrinkle Prevent feature, and
Signal On/Off. During the Rapid Refresh Cycle you can change the
Wrinkle Prevent and Signal On/Off features. To change other
settings, press START-PAUSE twice to stop the dryer and clear the
settings. Select another cycle or option.
Air Dry
Use the Air Dry temperature for items that require drying without
heat such as rubber, plastic, and heat-sensitive fabrics. This chart
shows examples of items that can be dried using Air Dry or Air Only.
Type of Load Time*
(Minutes)
Foam rubber - pillows, padded bras, stuffed toys 20 - 30
Plastic - Shower curtains, tablecloths 20 - 30
Rubber-backed rugs 40 - 50
Olefin, polypropylene, sheer nylon 10 - 20
*Reset time to complete drying, if needed.
When using Air Dry or Air Only
■ Check that coverings are securely stitched.
■ Shake and fluff pillows by hand periodically during the cycle.
■ Dry item completely. Foam rubber pillows are slow to dry.
NOTE: Sensor Cycles are not available when using the Air Dry or
Air Only setting.
Additional Features
You may follow the progress of your dryer with the drying Status
indicator lights.
WRINKLE PREVENT Feature
When you are unable to remove a load of clothes from the dryer as
soon as it stops, wrinkles can form. The WRINKLE PREVENT feature
periodically tumbles, rearranges, and fluffs the load to help keep
wrinkles from forming.
■
Press the WRINKLE PREVENT feature to get up to 120 minutes of
heat-free, periodic tumbling at the end of a cycle. The Wrinkle
Prevent indicator light blinks when this option is selected and
that part of the cycle is occurring.
■
Stop at any time by pressing the WRINKLE PREVENT feature or
opening the dryer door.
■ Other cycles will retain the WRINKLE PREVENT feature setting.
(For example, if you select the WRINKLE PREVENT feature in the
Normal cycle, the WRINKLE PREVENT feature will be on the
next time you select the Normal cycle.)
NOTE: If you do not select the WRINKLE PREVENT feature, the dryer
stops after the cool down period.