Maytag MHW8000Y, Use & Care Manual

Page: 13 / 52

13
WASHER MAINTENANCE
13.
Remove garments promptly
after cycle is finished
Promptly remove garments after cycle has
completed to avoid odor and rusting of
metal objects on garments. When unloading
garments, pull back the door seal and check
for small items between the tub and the basket.
If you will be unable to remove the load
promptly, use the Fresh Hold
®
option. If the
Fresh Hold
®
option is selected, the washer will
automatically activate the fan and tumble
the load periodically for up to 16 hours.
NOTE:
n
After any wash cycle is completed,
the door must be opened and then
closed before a new cycle can begin.
n
A small amount of water may remain in the dispensers after
the wash cycle is complete. This is normal.
n
This washer has a tight seal to avoid water leaks. To avoid
odors, leave the door open to allow the washer to dry
between uses.
WASHER CARE
Recommendations to Help Keep Your Washer Clean
and Performing at its Best
1. Always use High Efficiency (HE) detergents and follow the
HE detergent manufacturer’s instructions regarding the
amount of HE detergent to use. Never use more than the
recommended amount because that may increase the
rate at which detergent and soil residue accumulate inside
your washer, which in turn may result in undesirable odor.
2. Use warm or hot water washes sometimes (not exclusively
cold water washes), because they do a better job of
controlling the rate at which soils and detergent accumulate.
3. Always leave the washer door slightly ajar between uses
to help dry out the washer and prevent the buildup of
odor-causing residue.
Cleaning Your Front Loading Washer
Read these instructions completely before beginning the
routine cleaning processes recommended below. This
Washer Maintenance Procedure should be performed,
at a minimum, once per month or every 30 wash cycles,
whichever occurs sooner, to control the rate at which soils
and detergent may otherwise accumulate in your washer.
Cleaning the Door Seal
1.
Open the washer door and remove any clothing or items
from the washer.
2. Inspect the gray colored seal between the door opening
and the drum for stained areas or soil buildup. Pull back
the seal to inspect all areas under the seal and to check
for foreign objects.
3. If stained areas or soil buildup are found, wipe down
these areas of the seal using either of the following
two procedures:
a. Affresh
®
Grit Grabber™ Cloth Procedure:
i. When the cycle is complete, gently pull back the
rubber door seal and clean the entire surface with
the rough side of the Grit Grabber™ cloth.
b. Dilute Liquid Chlorine Bleach Procedure:
i. Mix a dilute bleach solution, using 3/4 cup (177 mL)
of liquid chlorine bleach and 1 gallon (3.8 L) of warm
tap water.
ii. Wipe the seal area with the dilute solution, using
a damp cloth.
iii. Let stand 5 minutes.
iv. Wipe down area thoroughly with a dry cloth and let
washer interior air dry with door open.
IMPORTANT:
n
Wear rubber gloves when cleaning with bleach.
n
Refer to the bleach manufacturer’s instructions
for proper use.
start
pause
press and
hold to start
12.
Press and hold START/PAUSE
to begin wash cycle
Press and hold the START/PAUSE button to start the wash
cycle. To pause a cycle in progress, press the START/PAUSE
button once, then press and hold again to continue the cycle.
To cancel a cycle, press the POWER/CANCEL button.
Once you press and hold START/PAUSE, you will hear the
door lock, unlock, and lock again. The washer door will remain
locked during the wash cycle.
Unlocking the door to add garments:
If you need to open the door to add 1 or 2 missed garments,
you may do so while the “Add a Garment” light is lit.
Press START/PAUSE once; the door will unlock
once the washer movement has stopped.
This may take several minutes. Then close
door and press START/PAUSE again to restart
the cycle.
start
pause
press and
hold to start