manualshive.com logo in svg

maxxess eMAX-LP4502, Installation Manual And Specification, Page: 16 / 20

Share
Download
maxxess eMAX-LP4502 Installation Manual And Specification Download Page 16

 

 

 

 

 

 

February, 2019 

              eMAX-LP4502-Man 

Page 16 of 20

  

Appendix A - Configuring the eMAX-LP Controllers  

 
The eMAX-LP controllers include an internal web page for configuring the communication parameters of 
the device.  It is recommended that the device be preconfigured in a controlled environment before 
installing the device on site. 

 

Default IP is 192.168.6.12 
Default user and password is 

admin

 and 

password 

 

Configuration of the eMAX-LP controller requires the following information.   

 

•

 

IP Address  

_____.______.______._____ 

•

 

Subnet Mask  _____.______.______._____ 

•

 

Gateway IP 

_____.______.______._____ 

 

Connecting to the eMAX-LP controller

 

 

1.  Connect the device to a computer using a standard network cable.   

 

2.  Set the computer

’s IP to a Statis IP Address of 192.168.6.10. 

3.  At the eMAX-LP Controller, be sure to turn dipswitch #1 to the ON position.  This enables the use of 

the DEFAULT Login credentials, and will time out in 5 minutes. 

 

4.  Connect to the device from your browser using 

http://192.168.6.12

.  The following screens will 

appear.  

 

 

This message may be different, depending on the version of Operating System that you have installed. 

First Click on 

“ Details “, which will tell you that your PC does not recognize the Web Pages’s Security 

Certificate.  This is Normal.  Then click on 

“ Go on to the webpage “. 

Summary of Contents for eMAX-LP4502





















Reviews:

No comments