background image

 

 

 

              

 

 

February, 2018 

              eMAX-EP4502 - Manual 

Page 11 of 11

  

 

Warranty 

Maxxess Systems, Inc. warrants the product is free from defects in material and workmanship  under normal 
use and service with proper maintenance for one year from the date of factory shipment.  Maxxess Systems, 
Inc.  assumes  no  responsibility  for  products  damaged  by  improper  handling  or installation.    This  warranty  is 
limited to the repair or replacement of the defective unit. 

There are  no expressed  warranties  other  than  set  forth herein.    Maxxess  Systems,  Inc  does  not  make,  nor 
intends, nor does it authorize any agent or representative to make any other warranties, or implied warranties, 
and expressly excludes and disclaims all implied warranties of merchantability or fitness for a particular purpose. 

Returns  must  be  accompanied  by  a  Return  Material  Authorization  (RMA)  number  obtained  from  customer 
service, and prepaid postage and insurance. 

 

Liability

 

The Interface should only be used to control exits from areas where an alternative method for exit is available.  
This product is not intended for, nor is rated for operation in life-critical control applications.  Maxxess Systems, 
Inc. is not liable under any circumstances for loss or damage caused by or partially caused by the misapplication 
or malfunction of the product.  Maxxess System, Inc. liability does not extend beyond the purchase price of the 
product. 

 

Summary of Contents for eMAX-EP4502












Reviews: