Maxwell MW-2115, Manual Instruction

Page: 9 / 28

9
ENGLISH
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES
IS PROHIBITED.
BEFORE THE FIRST USE
In case of the unit transportation or storage
at low temperature keep it for at least three
hours at room temperature.
–
Remove all stickers and packaging elements
that can prevent the unit operation.
– Unwind the power cord to its full length.
–
Check the unit for damages; do not use a
damaged unit.
–
Before plugging the unit in make sure that the
operating voltage of the unit corresponds to
the voltage of your mains.
Blades
–
If the blades have been removed for cleaning
or replacement, install them back, adjust and
tighten the fastening screws (pic. 1).
Blade shifter (2) (pic. 2)
–
When you cut hair without using attachments
(5, 6, 7, 8), you can shift the blade to adjust
the cutting length.
–
In the upper shifter (2) position, haircut will
be the shortest.
–
In the lower shifter (2) position, the cutting
length is approximately the same as when
using 3 mm attachment comb (5).
– By changing the position of the shifter (2)
while cutting hair, you can select the neces-
sary cutting length.
–
If hair is jammed in the blades while cutting,
move the shifter (2) from the upper posi-
tion to the lower position several times, this
will help to release the jammed hair without
removing the blades.
–
When the hair clipper is switched on, move
the shifter (2) several times from the upper
position to the lower position, this way you
can remove the cut-off hair from the blades.
– If the hair clipper pulls hair while cutting, it
means that the blades became blunt, replace
them with new ones.
Lubricating oil
– To maintain the unit in a good condition, you
should lubricate the blades periodically. Do
not use vegetable oil or oil that includes sol-
vents. Solvents are subjected to evaporation,
and the remaining thick oil can slow down the
upper blade moving speed.
–
For lubricating the blades use only the oil (11)
supplied with the unit.
HAIR STYLING INSTRUCTIONS
• Hair should be clean and dry during hair cut-
ting.
•
Insert the power plug into the mains socket.
• Before cutting hair switch the hair clipper on,
moving the power switch (4) to the position
«
ON » and make sure that hair clipper oper-
ates normally and the blades move smoothly.
If there is excess oil on the blades, switch the
hair clipper off setting the power switch (4) to
the position «
OFF » and remove the excessive
oil with a dry cloth.
•
Constantly check the power cord, prevent it
from multiple twisting, regularly switch the
unit off and straighten the power cord.
•
Seat a person so that his/her head is approxi-
mately at your eye level, cover the person’s
shoulders with a towel and set hair with the
comb.
Reminder
–
Always cut off a little amount of hair at a time;
if necessary you can always return to the cut
off part and trim off additional hair.
–
The best haircutting results are reached on
dry hair, not wet.
–
Comb the hair to reveal uneven locks.
– It is better to leave longer hair after cutting
for the first time.
–
After learning your clipper better, you will
be able to arrange your hair in any style you
need.
Attachment combs
The hair length after cutting depends on the
attachment used:
–
attachment comb (5): length of hair left 3 mm
–
attachment comb (6): length of hair left 6 mm
–
attachment comb (7): length of hair left 9 mm
– attachment comb (8): length of hair left 12 mm
Install the selected attachment comb on the
blades, teeth up, and press on the ledge in
the bottom part of the attachment until lock-
ing. Before cutting hair make sure that the
attachment is locked on its installation place. To
remove the attachment comb press the clamp
and remove the attachment.
IM MW-2115.indd 9 28.08.2018 11:49:29