Maxwell MW-2115 Manual Instruction Download

Page: 10 / 28

ENGLISH

Step one

Set the 3 mm attachment comb (5) or 6 mm
attachment comb (6). Switch the unit on using
the power switch (4), setting it to position «

».

Hold the hair clipper with the blades pointed
upwards. Start cutting from the beginning of the
hair growth. Slowly move the trimmer upwards.
This way cut the head back area at neck bottom
and near the ears (pic. 3, 4, 5).

Step two

Switch the hair clipper off with the power switch
(4) by setting it to the position «

OFF

», unplug the

unit, then set the 9 mm attachment comb (7) for
longer hair or 12 mm attachment comb (8) and
continue cutting hair near top of the head (pic. 6).

Step 3 – cutting in the temples area

Switch  the  hair  clipper  off  and  unplug  it,  then
set  the  3  mm  attachment  comb  (5)  or  6  mm
attachment comb (6) and cut hair in the area of
temples.  Then  set  the  9  mm  attachment  comb
(7) or 12 mm attachment comb (8) and continue
cutting towards the top of the head (pic. 5).

Step 4 – cutting the crown of the head

Using the 9 mm attachment comb (7) or 12 mm
attachment comb (8), cut the hair on the top
of the head towards the crown against the hair
growth direction (pic. 6).

•

You can cut hair against and along the direc-
tion of hair growth, but keep in mind that the
hair cut against the growth will be shorter
than the hair cut along the growth.

•

Use the 3 mm attachment comb (5) and 6 mm
attachment comb (6) for very short haircut. To
leave a little longer hair, use the 9 mm attach-
ment comb (7) or 12 mm attachment comb (8).

•

To leave longer hair, grip hair locks between
your fingers and cut the hair off using the
clipper (pic. 7).

•

You can use the comb: lift the hair locks
and cut them with the hair clipper above the
comb (9) (pic. 8).

•

Always start cutting from the head back.

•

Comb (9) the hair to reveal uneven locks.

•

Use scissors (10) to trim hair.

Step 5 – the final part

–

In the final stage of hair cutting remove the
attachment comb from the unit, turn the

blades of the clipper towards the hair and
trim hair on the temples and neck carefully.
Do not press the clipper strongly, there is
danger of injuries or cuts when open blades
come in contact with skin (pic. 9).

Cone-shaped haircut

Set  the  necessary  attachment  comb  and  start
cutting from the head back towards the crown.
Cut hair against hair growth from the head front
to the crown and from the sides (pic. 10). To get
a  flat  top  haircut,  use  the  comb:  lift  the  locks
and cut them along the comb. Comb the hair to
reveal uneven locks.
After you finish cutting hair, switch the hair clipper
off  setting  the  power  switch  (4)  to  the  position

«OFF»

and take the power plug out of the socket,

put the protective cover (1) on the blades.

CLEANING AND CARE
Lubricating the blades

Regularly lubricate the blades using the oil (11)
supplied with the unit.

–

Switch the unit off using the power switch (4)
and unplug it.

–

Apply one-two drops of oil (11) on the teeth
of the blades and the back side of the upper
blade, switch the unit on and make sure that
the blades are moving smoothly.

–

Switch the hair clipper off, clean the excess
oil with a dry cloth.

Attention! Use only the oil (11) supplied with
the unit.

DO NOT USE vegetable oil, fat, oil mixed with any
solvents for lubricating.
Solvents will evaporate, leaving thick grease that
may slow down the blades’ motion.

Cleaning the hair clipper

–

Switch the hair clipper off and unplug it.

–

Clean the blades from hair, using the clean-
ing brush (12).

–

Wipe the accessories and the unit body (3)
with a slightly wet cloth, and then dry them
with a soft cloth.

–

Put the protective cover (1) on the blades.

–

Do not immerse the hair clipper, the power
cord and the plug into water or any other
liquid.

–