MaxStream 9XCite XC09-009 Series Product Manual Download Page 5

Page: 5 / 37

Distributor of Digi International: Excellent Integrated System Limited

Datasheet of XC09-009-DK - KIT DEV FOR 900MHZ 9600BPS 1MW
Contact us: [email protected] Website: www.integrated-circuit.com

9XCite™

OEM

Module

–

Product

Manual

v2.1

[2007.01.04]

2007

MaxStream,

Inc.

9XCite

OEM

Module

The XCite OEM RF Module provides OEMs and system
integrators with a low power wireless solution that is
easy-to-use.

No configuration is necessary for out-of-box RF opera-
tion. Simply feed data into one module; then the data is
sent out the other end of the wireless link. If more
advanced functionality is needed, the module support
an extensive set of commands.

The RF module operates within the ISM 900 MHz fre-
quency band.

1.1. Key Features

Long Range Data Integrity

4 mW Power Output (0 dBm)

• Indoor/Urban: up to 300' (90 m)
• Outdoor RF line-of-sight:

up to 1000' (300 m) w/ 2.1 dB dipole antenna

Receiver Sensitivity

• -108 dBm (@ 9600 baud),
• -104 dBm (@ 38400 baud)

Advanced Networking & Security

True Peer-to-Peer (no "master" required),
Point-to-Point & Point-to-Multipoint networking

Hopping (Frequency Hopping Spread Spectrum)
or Single Frequency Modes

7 hopping channels: each with over 65,000

network addresses available

Up to 9 non-overlapping simultaneous networks

Low Power

Power-down current as low as 20 µA

55 mA transmit / 45 mA receive current

consumption

Easy-to-Use

No configuration required

Advanced configurations available through A
commands

2.85 to 5.50 VDC power supply

Continuous RF data stream of

up to 38.4 kbps

XII™ Interference Immunity

X-CTU Software included

Cover more ground with fewer radio

modems due to market-leading range

Free & Unlimited Technical Support

1.1.1. Worldwide Acceptance

FCC Certified (USA) [Refer to Appendix A for FCC Requirements]

Systems that contain XCite Modems inherit MaxStream's FCC Certification

IC (Industry Canada) Certified

ISM (Industrial, Scientific & Medical) license-free 902-928 MHz frequency band

Manufactured under ISO 9001:2000 registered standards

5 / 37

Summary of Contents for 9XCite XC09-009 Series






































Search results

Summary of Contents for 9XCite XC09-009 Series

Reviews:

Related manuals for 9XCite XC09-009 Series

Brands by name

Popular brands

MaxStream 9XCite XC09-009 Series, Product Manual

Search results

Summary of Contents for 9XCite XC09-009 Series

Reviews:

Related manuals for 9XCite XC09-009 Series

Brands by name

Popular brands