MaxStream 9XCite XC09-009 Series Product Manual Download Page 37

Page: 37 / 37

Distributor of Digi International: Excellent Integrated System Limited

Datasheet of XC09-009-DK - KIT DEV FOR 900MHZ 9600BPS 1MW
Contact us: [email protected] Website: www.integrated-circuit.com

9XCite™

OEM

Module

–

Product

Manual

v2.1

[2007.01.04]

2007

MaxStream,

Inc.

Contact MaxStream

Free and unlimited technical support is included with every MaxStream Radio Modem sold. For the
best in wireless data solutions and support, please use the following resources:

MaxStream office hours are 8:00 am - 5:00 pm [U.S. Mountain Standard Time]

Documentation:

www.maxstream.net/support/downloads.php

Technical Support:

Phone.

(866) 765-9885 toll-free U.S.A. & Canada

(801) 765-9885 Worldwide

Live Chat.

www.maxstream.net

E-Mail.

[email protected]

37 / 37

Summary of Contents for 9XCite XC09-009 Series






































Search results

Summary of Contents for 9XCite XC09-009 Series

Reviews:

Related manuals for 9XCite XC09-009 Series

Brands by name

Popular brands

MaxStream 9XCite XC09-009 Series, Product Manual

Search results

Summary of Contents for 9XCite XC09-009 Series

Reviews:

Related manuals for 9XCite XC09-009 Series

Brands by name

Popular brands