7
GB
OPERATING INSTRUCTION
1) BEFORE STARTING THE EQUIPMENT
1. Assembling the machine P
osition the machine base
(1). Fasten moun
ting flan
ge with pillar (2) using three screws (3) and washers to drill base (1).
Push the drill table (4) with drill table clamp sha
ft
onto the pillar (2) (Fig. 3). Lock the drill table into the
desir
ed position using the clamping sc
rew (5).
Place drill head (6) with V-belt cover (7) and motor (8) onto the drill pillar and fasten using the Allen screws
(20).
Screw the three ball-shaped handles (9) onto the feeder cross handle.
Note: All bare parts are greased in order to protect them from corrosion. Before moun
ting the drill chuck (10
)
onto the spindle (11), both parts must be completely degreased using an environmentally friendly solvent.
This ensures op
timal t
ransmission of power.
2. INSTALLING THE MACHINE (Fig. 1)
Before you use the drill for the
fi
rst
time
it must be permanently
fi
xed in
positi
on. Use both moun
ting
holes
(12) in the base plate to do this. Ensure that the equipment is freely accessible for opera
tion,
adjustment
and maintenance. Note: The
fixing
screws may only be
tig
htened to a point where they do not distort or
deform the base plate. Excessive tension can lead to fracture.
3. HINGED CHIP GUARD (Fig. 4-6)
Unscrew the three screws (21). Push the transparent cover (23) into the groove of the red moun
ting
frame
(24) and fasten it again with the screws (21). Then use the clamping screw to fasten the folding chip guard
(13) to the machine. Finally swing up the chip guard, push the scroll chuck (10) with a jerk onto the taper
and check that the tool is securely seated.
The height of the cover (23) is in
fini
tely adjustable and can be locked using both thumb screws (22).
The chip guard (13) can be
flipped
upwards to change drill bits, however ensure that the chip guard (13) is
back in its initial position b
efore rest
arting the equipme
nt.
4) PRIOR TO USING THE MACHINE FOR THE FIRST TIME
Ensure that the voltage of the mains supply complies with the
specifi
ca
tions
on the ra
ting
plate. Connect
the equipment only to a socket with the properly installed earthing contact. The drill is equipped with a
no-volt trip that is designed to protect the operator from an undesired restart following a drop in voltage.
Should this happen, the equipment must be physically restarted.
5) OPERATION
1. General (Fig. 2)
To switch on the equipment, push in the green On bu
tt
on “I” (18); the drill starts up. To switch o
ff
, press the
red O
ff
bu
tt
on “O” (19); the drill shuts down. Ensure that you do not overload the equipment. If the sound
of the motor drops in pitch during opera
tion,
it is being overloaded. Do not overload the equipment to the
point where the motor comes to a stands
till.
2. Fi
tting
tools to the drill chuck (Fig. 1)
Make sure that the power plug is removed from the socket-outlet before changing tools. Only cylindrical
tools with the s
tipul
ated maximum sha
ft
diameter may be clamped in the drill chuck (10). Only use a tool
that is sharp and free of defects. Do not use tools whose sha
ft
is damaged or which are deformed or
fl
awed
in any other way. Use only accessories and a
tt
achments that are
specified
in the opera
ting
ins
tructions
or
have been approved by the manufacturer.
3. Using the quick-change drill chuck
Your drill is equipped with a gear-toothed drill chuck (10). In order to insert a drill bit,
flip
up the chip guard
(13), insert the drill bit, then
tig
hten down the drill chuck using the supplied chuck key. Pull out the chuck
key. Ensure that the clamped tool is
firmly
seated. Important. Do not leave the chuck key in the clamp hole.
Doing so will cause the chuck key to be catapulted out, which could cause injury.
4. Se
tting the speed (Fig. 1/8/9)
First switch the equipment o
ff
, then pull the power plug. The various spindle speeds can be set by moving
