Maxcess MAGPOWR DFC-90 Instruction Manual Download Page 20

Page: 20 / 20

7-1

SERVICE

Maintenance

The only maintenance that may be required on the DFC-90 is
fuse replacement.

1. Shut off AC power to the DFC-90 unit.
2. Remove the enclosure top by inserting a flat blade

screwdriver under the retaining tabs in the base
(See Figure 2, page 3-1).

3. Replace fuse(s).
4. Reinstall the enclosure to maintain the IP rating.

Service requests and
replacement parts

To request service or to get replacement parts, contact one of
the following addresses:

Fife Corporation
222 West Memorial Rd.
Oklahoma City, OK, 73114,
USA
Phone:  1.405.755.1600
Fax: 1.405.755.8425
Web:  www.maxcessintl.com

Fife-Tidland GmbH
Max-Planck-Strasse 8
65779 Kelkheim

Deutschland
Telefon: +49.6195.7002.0
Fax:  +49.6195.7002.933
Web:  www.maxcess.eu

Siemensstrasse 13-15
48683 Ahaus
Deutschland

AMERICAS

Tel +1.405.755.1600

Fax +1.405.755.8425

[email protected]

www.maxcessintl.com

EUROPE, MIDDLE EAST

AND AFRICA

Tel +49.6195.7002.0

Fax +49.6195.7002.933

[email protected]

www.maxcess.eu

CHINA

Tel +86.756.881.9398

Fax +86.756.881.9393

[email protected]

www.maxcessintl.com.cn

INDIA

Tel +91.22.27602633

Fax +91.22.27602634

[email protected]

www.maxcess.in

JAPAN

Tel +81.43.421.1622

Fax +81.43.421.2895

[email protected]

www.maxcess.jp

KOREA, TAIWAN,

AND SE ASIA

[email protected]

www.maxcess.asia

Summary of Contents for MAGPOWR DFC-90





















Search results

Summary of Contents for MAGPOWR DFC-90

Reviews:

Related manuals for MAGPOWR DFC-90

Brands by name

Popular brands

Maxcess MAGPOWR DFC-90, Instruction Manual

Search results

Summary of Contents for MAGPOWR DFC-90

Reviews:

Related manuals for MAGPOWR DFC-90

Brands by name

Popular brands