background image

 

 

  Battery pack breakdowns 

 

If the following conditions occur, bring the Battery and Charger to your dealer. 

 

  If the red charging lamp does not flash when the charger plug is inserted into an AC 230V main power 

source outlet (When the battery pack is not inserted in the charger.) 

  If neither the red charging lamp nor the orange standby lamp lights or flashes when the battery pack is 

inserted in the charger. 

  If the orange standby lamp does not change to the red charging lamp even for more than 1 hour. 

  If the red charging lamp does not change from constant to flashing light even after more than 30 minutes 

have passed since starting charging. (Except during low temperature charging.) 

 
 
 

  Service Life of the Battery Pack   

If any condition described below is observed, the battery pack is at the end of its service life. Replace it with a 
new one.

 

 

  Although the battery pack has been properly charged (fully charged), a great drop in hours of use has been 

noticed. 

 
 
 

Don’t charge the battery pack when this happens. If the motor’s rotational speed slows down, the 
power of the battery pack is considered to be nearly depleted. Using the tool more will cause it to over 
discharge, resulting in a shortened service life of the battery pack and also in functional trouble of the 
tool’s main body. 
 
 
 
Don’t use a battery pack when its service life is finished. 
This will cause functional trouble in the tool’s main body. Also charging a battery pack that is out of 
service life will lead to functional trouble in the battery charger. 

 
 
 

  Recycling a NiCad Battery 

 

The MAX battery pack uses a NiCad battery, it may be illegal to dispose of this battery into the municipal 
waste system. Check with your local solid waste officials for details in your area for recycling options or proper 
disposal.

 

 
 
 
When disposing of the battery pack, make sure to put a pack cap on its terminal (with insulating tape 
securing it) to prevent short circuits. 
 
 
 

  Preventing the Battery Pack from Becoming Inactive   

When the tool is purchased, or when it is not used for extended periods (more than two months), the battery 
pack must be charged for 24 hours to reach top performance.

  13

Summary of Contents for RB215























Reviews: