manualshive.com logo in svg

Max Machinery 213, Operational Manual

Share
Download
Max Machinery 213 Operational Manual Download Page 12

Max Machinery, Inc. 210 Series User Manual  © Copyright 2013 

Rev. 002Q4 

 12

 

Analog

Mating Cable  
Wire Color

Turck 

Pin #

Case Ground

Blue

3

Common

Black

4

Power **

Brown

1

Signal Output (+)

Grey

5

Signal Output (-)***

White

2

WARNING

Installation and removal should only be facilitated by trained personnel

Verify transmitter output type (ANALOG or FREQUENCY) before wiring, inappropriate wiring could 

result in damaging the circuit.

Removal note: The transmitter does not need to be removed from the flow meter for any field servicing or adjustments. 
Normally, the flow meter and transmitter are shipped back to the factory for calibration or service as a unit. If the 
transmitter needs to be removed from the flow meter for installation, be sure to retighten the transmitter snugly in 

order to ensure proper sensor alignment. 

Mechanical Installation

1. The transmitter is attached to the flow meter’s threaded magnet shield. Hand tighten only. (~ 3 ft-lb)

2. The transmitter lid has four thread paths. To realign the cable, remove the lid and rotate up to 180° and retighten 
using an alternate starting point. Tighten to compress the O-ring seal.

Removal
1. Remove electrical connections
2. Unscrew transmitter, using a wrench if necessary.

Moisture Seal Protection
On all models, the housing is designed as a liquid and vapor-tight enclosure. There are O—ring seals at the lid and 

possibly also the base of the housing — these need to be fully seated. A properly sealed transmitter will prevent the 

formation of damaging moisture inside the housing.
Turck connector Model: The connector is sealed to the lid at the factory and is ready for use.
NPT Model: To ensure a moisture-tight seal, apply appropriate sealant to the threads at installation.

Wiring ANALOG

The electrical connector versions are pre-wired inside the transmitter and ready to accept a mating cable (available from 
the factory). The liquid-tight, NPT models need to be wired during installation as shown in the table below:

*Model 29X-xxx-000, 24vdc powered, Model 29X-xxx-100, 12vdc powered
** Signal output is fully isolated: If attached to a true differential input a 10K Ohm pulldown resistor
     should be installed between (—) and common at the receiving end.

Electrical Installation - Wiring

Summary of Contents for 213





















Reviews:

No comments

Brands by name

Popular brands

Load more brands