background image

permissible by law and at it’s option to:
•  replacing the products or the supply of equivalent goods;
•  the repair of the products;
•  the payment of the cost of replacing the products or of acquiring 

equivalent goods; or

•  the payment of the cost of having the products repaired.

To the extent permitted by law, all other warranties whether implied or 

otherwise, not set out in these warranty terms and conditions are excluded 

and we are not liable in contract, tort (including, without limitation, 

negligence or breach of statutory duty) or otherwise to compensate the 

customer for:
•  any increased costs or expenses;
•  any loss of profit, revenue, business, contracts or anticipated savings;
•  any loss or expense resulting from a claim by a third party; or
•  any special, indirect or consequential loss or damage of any nature 

whatsoever caused by Matson’s  failure in complying with its 

obligations.

MATSON IS NOT RESPONSIBLE FOR DAMAGE THAT OCCURS AS 

A RESULT OF YOUR FAILURE TO FOLLOW THE INSTRUCTIONS 

INTENDED FOR THE MATSON PRODUCT

In the following paragraph, “Our” means Matson and “You” means the 

customer:

Our goods come with guarantees that cannot be excluded under the 

Australian Consumer Law. You are entitled to a replacement or refund for 

a major failure and for compensation for any other reasonably foreseeable 

loss or damage. You are also entitled to have the goods repaired or 

replaced if the goods fail to be of acceptable quality and the failure does 

not amount to a major failure.

The benefits given to the customer in this warranty are in addition to other 

rights and remedies under a law in relation to the products to which this 

warranty applies.

Summary of Contents for MA98411

























Reviews: