background image

© 2015 Johnson Health Tech. All Rights Reserved.

VARSIT Y  SERIES

VY-D691-05 / DOUBLE HALF RACK

Rev 1.0

MAINTENANCE CHECKLIST

ACTION

FREQUENCY

Clean Upholstery *

Daily

Inspect Cables

Daily

Clean Guide Rods

Monthly

Inspect Hardware

Monthly

Inspect Frame

Bi-Annually

Clean Machine

As Needed

Clean Grips *

As Needed

Lubricate Guide Rods †

As Needed

* Upholstery & Grips should be cleaned with a mild soap and water or 

a non-ammonia based cleaner.

† Guide rods should be lubricated with Teflon based lubricant. Apply the 

lubricant to a cotton cloth and then apply up and down the guide rods.

PRODUCT SPECIFICATIONS

TECH SPECS

Maximum User Weight

181.5 kg / 400 lbs.

Maximum Training Weight

363 kg / 800 lbs.

Product Weight

211 kg / 465 lbs.

Overall Dimensions

(L x W x H)*

218.5 x 187 x 236.5 cm /

86” x 73.5” x 93”

Weight Horn Diameter  

(Weight Plate Storage)

47.63 mm / 1.875”

* Ensure a minimum clearance width of 0.6 meters (24”) for access to 

and passage around MATRIX strength equipment. Please note, 0.91 

meters (36”) is the ADA recommended clearance width for individuals 

in wheelchairs.

WARRANTY

For North America, please visit 

www.matrixfitness.com  

for warranty information along with warranty exclusions  

and limitations.

PROPER USAGE

1.  Do not exceed weight capacity of this 

equipment.

2.  If applicable, set safety stops to 

appropriate height.

3.  If applicable, adjust seat pads, leg 

pads, foot pads, range of motion 

adjustment, or any other type 

of adjustment mechanisms to a 

comfortable start position. Make 

certain that the adjusting mechanism is 

fully engaged to prevent unintentional 

movement and to avoid injury.

4.  Sit on bench (if applicable) and get into 

appropriate position for exercise.

5.  Exercise using no more weight than 

you can safely lift and control.

6.  In a controlled manner, perform 

exercise.

7.  Return weight to its fully-supported 

start position.

Summary of Contents for VARSITY Series






Reviews: