Matrix MW001 Manual For Installation, Use And Maintenance Download Page 10

Programme Listing

Programme 

names and 

temperatures

Intensive

70

O

 

wash

Normal

55

O

 

wash

Light 

50

O

 

wash

Quick wash

40

O

 

wash

Prewash

No heat

Level of soil

High

Medium

Small

Small

NA

Detergent 

amount

P Main

Compartment (g)

5+25

5+25

5+25

0 +15

0

Programme 

duration 

(mins.)

standard/

quick

112

102

162

32

12

Electricity 

consumption 

(kW hours)

standard/

quick

1.62

1.24

1.05

0.40

0.02

Water 

consumption 

(litres)

standard/

quick

18

16

15

9

3

Hot prewash

70

O

 

wash

Cold rinse

Hot rinse

Dry

End

Cold prewash

55

O

 

wash

Cold rinse

Hot rinse

Dry

End

50

O

 

wash

Cold rinse

Hot rinse

Dry

End

40

O

 

wash

Cold rinse

End

Prewash

End

The values and times provided above have been obtained under laboratory conditions according to relevant standards. This 
information can change depending on the conditions of the dishwasher’s use and environment. (mains supply voltage, water 
pressure, water input temperature and environment temperature).

Laboratory measured value in accordance with European standard EN50242 with rinse aid setting.

9

Cold prewash

Summary of Contents for MW001

















Reviews: