Matrix MFU800 Installation Manual Download Page 3

3

Important

Never store inflammable or explosive items and strong corrosive acids or alkalis in the appliance.

This is a household appliance, which is produced in accordance with the national standard. It is intended for food storage only, not 
for storage of blood, medicine and biological products.

To prevent risk of fire, keep the appliance away from petrol or any other inflammables.

To prevent risk of electromagnetic interference or other accidents, do not place a microwave oven on top of the refrigerator or 
use any electric appliance inside the refrigerator.

Do not allow children to play with or near the appliance.

The internal surface of freezer compartment is very cold when the appliance is running. Do not touch the surface especially with 
wet hands.

Do not splash water onto the appliance. Keep it away from places of high humidity that may have adverse effect on the electric 
insulation performance.

Please remove the door, door seal and shelves before disposal of the old appliance and put them away in a safe place to prevent 
children from being entrapped.

Before first use

You must allow the freezer to settle for at least twenty four hours prior to switching the power on.

It is recommended that you clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda and warm 
water and then thoroughly drying the interior.

The freezer may have an odour to it at first use. This will disappear as the appliance cools.

Please note:

The appliance will work continuously until it comes down to the correct temperature.

If the appliance is switched off, you should allow five minutes before switching it on again to prevent unnecessary damage

to the compressor.

Never store inflammable or explosive items and strong corrosive acids or alkalis in the appliance.

Summary of Contents for MFU800

















Reviews: