background image

MSC-XD3232S Product Manual

ctl.serial.baud

Number RW

AS First serial port baud rate in bits/second.

ctl.serial.log

Boolean RW

AS First serial port protocol log enable.

ctl.serial.proto

String

RW

AS First serial port protocol selection (“mascot”, “svs”, etc).

ctl.serial2.baud Number RW

AS Second serial port baud rate in bits/second.

ctl.serial2.log

Boolean RW

AS Second serial port protocol log enable.

ctl.serial2.proto String

RW

AS Second serial port protocol selection (“mascot”, “svs”, etc).

mtx.serial

Number R

Current matrix serial number, incremented on every routing change.

mtx.sync

Boolean RW

AS Keep current routing state stored to preset 0.  Effectively retains last

matrix routing state even after a restart or power cycle.

net.dhcp

Boolean RW

S

Network interface DHCP enable.

net.gateway

IP

RW

S

Network gateway address.

net.ip

IP

RW

S

Network interface IP address.

net.mac

MAC

R

Network interface MAC address.

net.netmask

IP

RW

S

Network interface mask.

pnl.cmdEn

Boolean RW

AS Panel command macro enable.

pnl.ip

IP

RW

AS Remote IP address for panel interface to control.

sys.arch

String

R

System architecture (“Pyxis”, “Carina”, “Lynx”, etc).

sys.firmware

String

R

Firmware series and version (“Pyxis 1.1.7” for example).

sys.name

String

RW

AS System name identifier.

3.8 Core Commands

This section outlines commands considered to be core MASCOT protocol commands and consists of matrix 
routing, I/O label, preset, and other primary system commands.

Command 

Arguments

Description

DestNames

[Dest][Lvl][Label]

Destination I/O names command.

E

[0 | 1]

Matrix connection echo enable command.

Firmware

System firmware version.

Help

Command help reference.

MascotVer

Mascot protocol version.

MtxCfg

[0-7]

Current matrix config.

P

[Preset]

Recall a preset.

PAdd

(Preset)(Dest)(Src)[Lvl]

Add a connection to a preset.

PClr

(Preset)

Clear a preset to “No Change” values.

PsetNames

[Preset][Label]

Preset names command.

PSub

(Preset)(Dest)[Lvl]

Subtract a connection from a preset.

PView

[Preset]

View preset.

Quit

Quit TCP/IP telnet session.

Reboot

Reboot the system.

Page 24 of 60

© 2013-2019 Matrix Switch Corporation

www.matrixswitch

 

 corp.com

 

 

Summary of Contents for MSC-XD3232S





























































Reviews: