Matrix Switch Corporation MSC-XD164S Product Manual Download Page 41 | Manualshive

Page: 41 / 60

background image

MSC-XD164S Product Manual

The first command queries the current external panel interface setting (0: disabled). The second command
enables the external panel interface.

3.10.28 PanelRate Command

Protocol Version: 2.1

For changing remote button panel refresh rate. When a button panel is configured to control a remote router the
current connection status is refreshed at regular intervals. This command can be used to increase or decrease
the rate, which is saved and recalled on system power up. The default refresh rate is 5 seconds. This value is
stored and recalled on power up.

Command

Description

PanelRate

Query current panel refresh rate (in seconds).

PanelRate RATE

Set remote panel refresh rate in seconds.

Examples

>PanelRate

5

>PanelRate 1

>

The first command queries the current panel refresh rate, which returns 5 (default). The second command sets
the refresh rate to be 1 second.

3.10.29 PClr Command

Routers and MSC-GCP2U32 only

Clear a preset. For Preset 0 this sets all Destinations to Source 0. Other Presets are assigned “No Change” to
all Destinations. This command stores preset information which is available through system power cycles.

Command

Description

PClr PRESET

Clear a preset.

Example to clear preset 1

>PClr 1

>

3.10.30 ProtoSer Command

Carina series only
NOTE:

Superseded by the

ctl.serial.proto

and

ctl.serial2.proto

System Paramete

Query or assign the serial protocol. The only available option is currently the case insensitive value "Mascot",
however additional control protocols may be added in the future. Value is stored and recalled on power up.

Page 41 of 60

© 2013-2016 Matrix Switch Corporation

www.matrixswitch

«
...
39
40
41
42
43
...
»

Summary of Contents for MSC-XD164S





























































Reviews:

No comments

Related manuals for MSC-XD164S

Brand: Xantech Pages: 2

M800 Elite Series

Brand: 4B Pages: 12

Brand: National Instruments Pages: 23

Brand: Zektor Pages: 65

Brand: Hama Pages: 2

Brand: UniFi Pages: 8

Brand: Zamel Pages: 4

Brand: e+p Pages: 2

Brand: Videosec Pages: 5

Brand: GeoVision Pages: 7

Brand: DataParts Pages: 5

Brand: Edge-Core Pages: 60

Brand: steute Pages: 10

Brand: National Instruments Pages: 23

Hidden Ignition Switch

Brand: Booma-RC Pages: 16

Brand: Konig Pages: 52

Brand: AVLinx Pages: 10

Brand: Bryston Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands