background image

MSC-HD81AAS Product Manual

NOTE:

 Superseded by 

MtxGroup 

 

 C

   ommand

 

 

.

I/O pairing is used for pairing destinations/sources for 3D support.  When activated a router will appear to have 
half the number of physical destinations and sources.  A given matrix crosspoint change will cause 2 
destinations to be changed.  Each odd destination/source is paired with the next highest even number 
destination/source.  This option is stored and recalled on power on.  When enabling this feature on a 4x4 video 
router for example, it would appear as a 2x2 3D router where destination 1 & 2 are paired and 3 & 4 are paired, 
likewise for sources.  This setting is stored and recalled on power up.

Command

Description

PairIO

Query current value of I/O pairing configuration.

PairIO 0 | 1

Enable or disable I/O pairing (0: disable, 1: enable)

Example

>PairIO

0

>PairIO 1

>

The first command queries the current state of I/O pairing, the second enables it.

3.11.24 PanelCmd Command

Protocol Version: 3.0

Query and assign panel button/GPIO command macros.  This system provides a means to easily implement 
custom functionality in response to a panel button press or GPIO auxiliary port contact closure (button or switch
to ground).  Panel buttons and GPIO pins are specified by numeric ID.

Panel buttons are numbered beginning with ID number 1.  Panel button order depends on the panel, but 
generally has the top left button as button 1, followed by number 2 in the lower left corner, number 3 in the top 
second column, continuing to alternate between top and bottom rows till the last button (lower right hand 
corner).

GPIO auxiliary pins start with ID number 65 for GPIO pin 1.

NOTE:

 Panel commands must be enabled with the 

PanelCmdEn Command

 or by setting the pnl.cmdE

S

  ystem

 

 

P

  arameter

 

 

 to activate them.

Command

Description

PanelCmd

Query all assigned panel button/GPIO commands.

PanelCmd Button

Query a single panel button/GPIO command.

PanelCmd Button Command

Assign a panel button/GPIO command.  Assigning a blank command to a 
button or GPIO pin will clear the command (two consecutive single or double 
quotes represents an empty string).

Page 38 of 61

© 2013-2018 Matrix Switch Corporation

www.matrixswitch

 

 corp.com

 

 

Summary of Contents for MSC-HD81AAS






























































Reviews: