Matrix Orbital MOP-TFT480272-43G-BLM-TPC Hardware Manual Download Page 13

 

MOP-TFT480272-43G-BLM-TPC

 

12 

11.6

 

LCD pixel defect   

(bad dot) (defect type: MI) 

Checking item 

Judgment criterion 

Color bad dot-bright dot(R,G,B) 

two adjacent bright point 

three or more adjacent point 

total points for bad dot-bright dot 

Bad dot-dark dot 

two adjacent dark point 

three or more adjacent point 

total points for bad dot -dark dot 

patch bright dot 

Invisible with ND5%, it is OK. 

 

11.7

 

Dot and line defect   

(defect type: MI) 

Checking item 

Judgment criterion 

Figure 

Diameter(mm)\LCD Size 

S ≤5.0 Inch 

Dot defect 

D≤0.1 

allowed 

 

D=(a+b)/2 

0.1<D≤0.2 

0.2<D≤0.3 

0.3<D≤0.5 

D>0.5 

the distance between the two defect dot:DS≥5mm 

line defect 

Length(mm) 

Width(mm)  Judgement Criterion 

 

disregard 

W≤0.05 

allowed 

L≤5 

0.05<W≤0.1 

L>5 

W>0.1 

Concave point and air 
bubble for polarizer   

Size(mm) 

Judgement Criterion 

D=(a+b)/2 

D≤0.3 

allowed 

0.3<D≤1.0 

1.0<D≤1.5 

D>1.5 

Fold mark, linear scar for 
polarizer   

Length(mm) 

Width(mm)  Judgement Criterion 

 

disregard 

W≤0.05 

allowed 

1<L≤5 

0.05<W≤0.2 

L>5 

W>0.2 

*Notes: 

1. If the fold mark and linear scar for polarizer is visible with operating condition, the 
defect is judged with line judge 
2. If the fold mark and linear scar for polarizer is visible with non-operating condition, 
the defect is judged with the above judgment standard. 

 

 

Summary of Contents for MOP-TFT480272-43G-BLM-TPC


















Reviews: