Matheson 8058 FUM Operating Manual Download Page 10

Page: 10 / 46

- 10 -

LCD display

No.

Name

Function

(1)

Operating state display

Displays the operating status in the detection mode. Normal: Blinking

(2)

Flow check display

Displays the drawing status. Normal: Rotating

(3)

Gas concentration
display

Displays gas concentration and unit.

(4)

Alarm sound display

Displays the setting status of the alarm sound.

(5)

Operation sound
display

Displays the setting status of the operation sound.

(6)

Battery level icon

Displays a reference of the battery level.

(7)

Bar meter display

Displays the level of gas concentration with the bar meter

(8)

Mode display

Displays the measuring mode status.

(9)

Gas name and
message display

Displays the gas name and a message according to the function.

NOTE

•

The meanings of battery level icons are as follows:

:Sufficient /

:Low /

:Needs replacing the butteries

If the battery level further drops, the inside of the battery icon starts to blink (.

.).

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

Summary of Contents for 8058 FUM















































Search results

Summary of Contents for 8058 FUM

Reviews:

Related manuals for 8058 FUM

Brands by name

Popular brands

Matheson 8058 FUM, Operating Manual

Search results

Summary of Contents for 8058 FUM

Reviews:

Related manuals for 8058 FUM

Brands by name

Popular brands