matev SRM-VP 130 Original Operating Manual Download Page 4

 

Safety 

Page 4 

 

 

Safety 

Guidelines and instructions with which you must comply are summarized in this section. 

Persons who install, operate and maintain the snow plow must have read and understood 
this operating manual. 

2.1 

Intended use 

The snow plow should only be mounted on tractors with sufficient power. It is used for 
clearing snow on paths, roads, and public areas. Thanks to the pivoting halves of the 
snow plow, you can switch over from snow plow to conventional snow blade, depending 
on the implementation conditions. Depending on the condition of the snow the snow plow 
can be used in snow depths to a maximum of half the blade height. A front power lift with 
coupling triangle must be mounted on the tractor. 

 

 
 
Attention! 
Do not use the snow plow for grading tasks. 

 

In addition compliance with the service and maintenance guidelines is a component of in-
tended use. Moreover intended use includes exclusive use of original spare parts and 
supplemental equipment, or use of such parts and equipment that meet the technical re-
quirements specified by the manufacturer

.

 

 

All other uses are excluded. 

Non-intended use causes: 

 

Health hazards for the operator or for third parties 

 

Damage to the tractor and the attachments 

 

Environmental damage 

 

This will immediately invalidate the guarantee. 

To avoid accidents and reduce the risk of accidents the relevant accident prevention 
regulations and the other generally acknowledged occupational health and safety and 
road traffic regulations apply without limitation. 

Changes to the snow plow and/or the associated accessories that are not authorized by 
the manufacturer invalidate the guarantee and exclude any liability on the part of the 
manufacturer for damage due to the changes. 

 

2.2 

Qualification of personnel 

Only persons 18 years of age or older, or instructed persons should install, operate, and 
maintain the snow plow. The operator must have read and understood this operating ma-
nual. 

 

 

Summary of Contents for SRM-VP 130

















Reviews: