manualshive.com logo in svg

Matelec FPC-15007-CON, Owner'S Operation

Share
Download
Matelec FPC-15007-CON Owner'S Operation Download Page 12

12

AT A GLANCE

INDICATORS

PUSH BUTTONS

DISTRIBUTED BY:

INSTALLATION DATE:

SERIAL NUMBER:

KEYPAD

MANUFACTURED BY MATelec AUSTRALIA  

 

 

EMAIL: [email protected]

MATelec reserves the right to alter technical specifications without notice.

A quick reference to the

controller’s Keypad and

Indicator functions and

meanings.

POWER ON

Power is turned on.

LEVEL ALARM ON

A high level alarm has been 

present for the preset time.

FLASHING

A low level alarm is present.

ON STEADY

Pump switched on to run.

ON STEADY

A pump fault/overload has

occurred.

FLASHING 

A prime loss 

fault has occurred.

Silences  the  siren  and  if  held

down  for  3  seconds,  clears  all 

faults

If  selected  (the  LED  indicator 

will  confirm  if on)  the  particular

pump is set to Automatic

Pumping Mode

Turns pump off

If selected (the LED indicator 

will confirm if on) the pump is 

set to Manual Pumping Mode

POWER ON

LEVEL ALARM

PUMP ON

FAULT

AUTO

MAN

OFF

MUTE/

RESET

Summary of Contents for FPC-15007-CON













Reviews:

No comments

Brands by name

Popular brands

Load more brands