background image

MLPJ35T 5  03/13/18

MLPJ35T 3-1/2 Ton Low Profile Jack

1.  Always store the jack in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive dust, or any other harmful 

elements. The jack must be cleaned of water, snow, sand, grit, oil, grease and other foreign matter before using.

2.  The jack must be lubricated periodically in order to prevent premature wearing of parts. A general purpose grease must be applied to caster wheels, 

front axle, elevator arm, handle base pivot bolts, release mechanism and all other bearing surfaces. Worn parts resulting from inadequate or no 
lubrication are not eligible for warranty consideration. See page 4 for lubrication instructions.

3.  Every jack owner is responsible for keeping the jack labels clean and readable. Use a mild soap solution to wash external surfaces of the jack but not 

any moving hydraulic components.

4.  Inspect the jack before each use. Do not use the jack if any component is cracked, broken, bent, shows sign of damage or leaks hydraulic fluid. Do not 

use the jack if it has loose or missing hardware or components, or is modified in any way. Take corrective action before using the jack again.

This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to potential personal injury 
hazards. Obey all instructions to avoid possible injury or death.

PREVENTIVE MAINTENANCE

Important: Service jacks are self-contained devices used for lifting, but not sustaining, a partial vehicular load. In accordance with ASME-PASE Load  
Sustaining Test: “A load not less than the rated capacity…shall not lower more than 1/8" (3.18mm) in the first minute, nor a total of .1875" (4.76mm)  
in 10 minutes.” Lowering within this range is considered normal operation and is NOT a warrantable defect.

PROBLEM

ACTION

1. Unit will not lift rated load.

Purge air from hydraulic system by following procedure under SETUP.

2. Unit will not sustain rated load or feels “spongy” under rated load.

Purge air from hydraulic system as above.

3. Unit will not lift to full height.

Purge air from hydraulic system as above.

4. Unit will not lower completely.

Check oil level. Make sure hydraulic system is not overfilled.

5. Handle tends to raise up while the unit is under rated load.

Pump the handle rapidly several times to push oil past ball valves in power unit.

6. Unit still does not operate.

Contact customer service.

TROUBLESHOOTING

WARRANTY NOTICE

Hydraulic Warranty Policy

Matco® shop equipment and tools, excluding accessories, are warranted against defects in materials or workmanship for a period of 1 
year  from original purchase. We will repair or replace at our option any defective part or unit which proves to be defective in material or 
workmanship within this warranty plan. This warranty does not cover damage to equipment or tools arising from alteration, abuse or misuse, 
and does not cover any repairs or replacement made by anyone other than  Matco or its authorized service centers.

The foregoing obligation is Matco Tools sole liability under this or any implied warranty and under no circumstances shall we be liable for any 
incidental or consequential damages.

NOTE: Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may 
not apply to you.

Return equipment or parts to Matco Tools, or an authorized service center, transportation prepaid. Be certain to include your name and address, 
evidence of the purchase date, and description of the suspected defect.

If you have any questions about warranty service, please write to Matco Tools, Stow, OH 44224. This warranty gives you specific legal rights 
and you may also have other rights which vary from state to state.

Summary of Contents for MLPJ35T








Reviews: