Matco Tools DT4B Operating Instructions Manual Download Page 2

Page 2

1605093-14

3.5" DIGITAL TIRE INFLATOR

WITH HOSE

DT4B

1. Inflator's working pressure is 0.2-12 bar (3-175 psi), Max Inlet Pressure is 15 bar (218 psi).
2. If the pressure is between 7 bar and 17 bar, the actual value will still be shown on the LCD, but the Maximum 

Permit table Error +/- 3 psi is not guaranteed.

3. Maximum Pressure is above 17 bar, the LCD will show "----", no actual value, and the inflator may be damaged. 

Accuracy is as below according to European Community Council Directive 86/217/EEC 
0 - 58 psi +/- 1.2 psi 
59 - 174 psi +/- 2.0 psi

1. Remove tire valve cap.
2. With clip-on air chuck lever depressed, firmly press chuck onto tire valve stem and release lever, and ensure that 

no air leaks.

3. Press the grip to inflate. Press the grip half-way to deflate.
4. To turn on the inflator, press the ON/UNIT/LIGHT button. If it does not work, the inflator will be turned off 

automatically 90 seconds later.

5. When the inflator is on, press the ON/UNIT/LIGHT button to turn on the backlight in order to read the pressure in 

dark. The backlight will diminish automatically in 5 seconds. Backlight will not be activated by turning on the 
inflator, can only be activated by pressing the ON/UNIT/LIGHT button.

6. To change unit, when the inflator is on, press ON/UNIT/LIGHT button for at least 3 seconds. Then, press 

ON/UNIT/LIGHT button shortly  after to choose the desired unit. The unit chosen will be set as default for 
following usage.

7. The inflator’s battery is 2*AAA, if voltage is low, the low battery signal on the top left of the LCD display will be 

flashing continuously to remind user to change the battery.

8. The measuring range is 0.2-12 bar (3-175psi). Reading resolution is 0.01 bar (0.1psi). Maximum inlet pressure is 

15 bar (218psi).

OPERATING INSTRUCTION:

USAGE NOTES:

Peel back rubber sleeve

1.

Pry the cover open with fingernail or

flathead screwdriver (care to hold down cover,

as cover is under spring tension)

2.

Install 2 AAA batteries

in indicated orientation

3.

Snap battery cover shut

4.

Reinstall rubber sleeve

5.

To avoid the risk of personal injury, especially to the eyes, face or skin,

DO NOT direct the stream at any person.

IMPORTANT

BATTERY INSTALLATION INSTRUCTION

Summary of Contents for DT4B











Reviews: