background image

 

 

 

 

 

6

 

 

DC CURRENT (AMPS) 

Range Resolution 

Accuracy  Overload 

Protection 

40mA 10

μ

400mA 100

μ

±(1.5% of 
r5 
digits) 

0.5A/250V fast fuse 
Input Voltage 
Drop: <0.2V. 

*15A 10mA 

±(2.5% of 
r5 
digits) 

Unfused; 15sec maximum 
Input Voltage Drop: <0.2V. 

* A waiting period of at least 15 minutes is necessary between every 15 
second testing period. 

 

AC CURRENT TRMS 

[1]

 

NOTE: 

Specifications are AC-coupled true RMS.

 

Range Resolution 

Accuracy  Overload 

Protection 

40mA 10

μ

400mA 100

μ

±(2.0% of 
r5 
digits) 

0.5A/250V fast fuse 
(Input Voltage Drop: <0.2V. 

Frequency response:

 50 - 400 Hz 

 

[1]

 All ac ranges are specified from 1 % to 100 % of range. 

Below 5 % of range, add 6 counts. 

Because inputs below 1 % of range are not specified, it is 
normal for this and other true-rms meters to display nonzero 
readings when the test leads are disconnected from a circuit 
or are shorted together. For volts and amps, crest factor of 

3.

  

DIODE/CONTINUITY TESTS 

Function Range 

Resolution

Description 

Note 

Diode Test 

2V 

1mV 

Test Current: 
1±0.6mA 

Test Voltage: 
Approx. 2.8V 

Continuity 
Test 

400

Ω

 0.1

Ω

 Approx. 

120

Ω

 or 

less, buzzer 
(beeper) will sound 

Overload 
Protection: 
250V DC or AC 
RMS 

 
 
 
 
 
 

Summary of Contents for ADMM50

























Reviews: