background image

 

 

 

 

 

4

 

 

„

 

Automatic zero adjustment 

„

 

Over range indicator (except 15 A function). Displays "OL" 
on LCD 

„

 

Low battery indicator. Displays battery symbol 

 on LCD 

„

 

Automatic power shut off (after 10 idle minutes) 

„

 

Pollution Degree 2 

„

 

Measuring circuit category II 

„

 

Operating environment: 

Temperature - 32° to 104° F. (0° C to 40° C) 
Humidity - Less than 80% relative humidity (non-condensing) 
Altitude - up to 6562 ft (2000 meters) 

„

 

Storage environment: 

Temperature - 4° to 140° F (- 20° to 60° C) 
Humidity - Less than 90% relative humidity (non-condensing) 

„

 

Power Supply: One 9-volt battery 

„

 

Fuse: 0.500A/250V 5X20 mm (Radio Shack, GMA/270 
series; #270-1047) fuse 

„

 

Dimensions:  

Height - 6.81 in. (173 mm) 
Width - 6.57 in. (167 mm) (includes test lead clips) 
Depth - 1.69 in. (43 mm) 

„

 

Weight (including battery): approximately 9.1 oz (260 g) 

ELECTRICAL SPECIFICATIONS 

DCV 

Range Resolution 

Accuracy  Overload 

Protection 

400mV 100

μ

V 250V 

DC/AC 

RMS 

4V 1mV 

40V 10mV 

400V 

600V 

1V 

±(0.8% of 
r5 
digits) 

600V DC/AC RMS 

Input Impedance:

 10M

Ω

 for all ranges. 

 

Summary of Contents for ADMM50

























Reviews: