PAGE 2 OF 6 | AU SUPPORT 1800 237 425 WWW.MATCHMASTER.COM.AU | NZ SUPPORT 0800 237 425 WWW.MATCHMASTER.CO.NZ
To filter and amplify an FM signal, tap GAIN, select the gain
of the input FM signal (15 to 35dB) and tap to confirm.
Note: DAB should be added via V/U input 1-4.
After INPUT FM is configured, scroll up to the top of the
menu (INPUT FM), tap the rotary button and scroll right
to INPUT V/U 1. Tap INPUT V/U 1 to enter the menu to
configure input 1.
Rotate the rotary button to scroll down in the submenu of
INPUT V/U 1.
PRE-AMPLI: The internal amplifier is by default ON, only
in case of very strong incoming signals (if the strongest
channel on that input is higher than 80dB
µ
V), it is advised to
switch this OFF.
DC: Decide whether the input should provide power to an
external amplifier. Choose between OFF or 12 V. Note: If
the external amplifier needs 24 V, you can change this in
advanced settings (see further).
Tap Add Channel to add channel. Up to 6 channels can be
added at once.
First select the starting channel (e.g. CH5) and tap to
confirm. Then select the stop channel (e.g. CH7, this means
that you will add 3 channels). Tap to confirm. Then you
can convert them using the rotary button (e.g. CH5 to CH7
converts to CH8 to CH10) and tap to confirm.
Some other examples:
To add CH5 and convert to CH6,
select as follows: 5: 5 -> 6: 6
To add CH21-22-23 and convert to CH31-32-33, select as
follows: 21: 23 -> 31:33
1.6 Configuring the Profiler Revolution
Navigating Through The Menu:
Use the Johansson rotary/push button to navigate through
the menu. This is very straightforward and simple. The table
below shows how the rotary/push should be used:
Push
the button
2 seconds
to enter the
basic configuration.
Push
the button to
confirm your selections.
When
rotating
the button, you scroll
through the different screens.
Menu Overview:
INPUT FM
INPUT V/U
1-4
OUTPUT
ADVANCED
LOAD SD
PRESET
SAVE SD
PRESET
EXIT
GAIN
PRE-
AMPLIFIER
LEVEL
LANGUAGE
PRESET
X
CREATE
PRESET
LOCK
DC
SLOPE
REGION
DELETE ALL
NO LOCK
ADD
CHANNEL
VHF ATTN
DC
VOLTAGE
BANDWIDTH
S-BAND
FW
VERSION
SERIAL
NUMBER
FORMAT
CARD
Region/Country Settings:
IMPORTANT!
Before starting the configuration, it is advised
to set the correct region or country. Unpower the unit, push
the button and keep pushing the button while you repower
the unit.
Release the button when the display shows “RESET
FINISHED”. Now the product is reset and will ask you to
enter country or region. This will amongst others determine
the channel plan for VHF and UHF and the DC voltage for
the inputs (12 or 24V).
To activate the correct channel frequency plan, select the
country or region where the Profiler Revolution is situated.
Rotate to select and confirm by tapping the rotary button.
The default setting is Europe. The Profiler Revolution is also
operational in the following countries/regions: Australia,
Brazil, China, Hong Kong, Italy, New Zealand, Russia, South
Africa, UK and USA.
All the following menu items can be accessed without the
reset procedure.
Push the rotary button for 2 seconds to access the menu.
Input Settings
Tap the rotary button to enter the INPUT FM menu. Rotate
the button to navigate through the submenu.
• The power adapter can easily be replaced without
disconnecting the product. To do so, open the top left
plastic cover by pushing the click at the opposite side of
the mains connector
