manualshive.com logo in svg

MasterCraft 062-3503-8, Instruction Manual, Page: 6 / 18

Share
Download
MasterCraft 062-3503-8 Instruction Manual Download Page 6

headline bars

continuation tabs

notes

warnings

headline bars

continuation tabs

notes

warnings

model no. 062-3503-8 | contact us 1-800-689-9928

6

TECHNICAL SPECIFICA

TIONS

TECHNICAL SPECIFICATIONS

Temperature

32 to 77°F (0 to 25°C)

Impeller

Plastic

Solids handling

1/4” (6.3 mm) spherical

Discharge size

1 1/4” (3.2 cm) male national pipe thread (MNPT),
1 1/4” (3.2 cm) female national pipe thread (FNPT) with 
elbow

Seal 

Lip seal

Cable entry

8’ (2.55 m) quick-disconnect cord with male terminal 

Upper bearing

Ball bearing

Lower bearing

Ball bearing

Power 

12 V DC

Motor protection

Overload protection in lead

Construction material

Steel for motor house, plastic for volute and impeller

Maximum flow

2000 U.S. GPH (7571 L/hr)

Maximum head height

16’ (4.9 m)

MOTOR AND ELECTRICAL

SKU number

062-3503-8

Volt

12 V DC

Cord size

18 AWG

Cord type

SJTW

NOTE:

Do not reduce size of discharge pipe or hose below 1 1/4” (3.2 cm) diameter.
If discharge is too small, pump will overheat and fail prematurely.
This pump is designed for use as a residential sump only. Only pump
water with this pump.

Summary of Contents for 062-3503-8



















Reviews:

No comments