MasterCraft 062-3503-8 Instruction Manual Download Page 16 | Manualshive

Page: 16 / 18

MasterCraft 062-3503-8 Instruction Manual Download Page 16

headline bars

continuation tabs

notes

warnings

headline bars

continuation tabs

notes

warnings

16

model no. 062-3503-8 | contact us 1-800-689-9928

OPERA

TING INSTRUCTIONS

WARNING!

• Procedures not specifically explained in this manual must be performed only by a qualified technician.
• An acid-filled standard lead-acid battery contains sulfuric acid. Avoid contact with skin, eyes or clothing.

CARE AND MAINTENANCE

To prevent serious injury from accidental operation, unplug the pump from its electrical outlet
before performing any inspection, maintenance, or cleaning procedures.
To prevent serious injury from pump failure, do not use damaged equipment. If abnormal noise
or vibration occurs, have the problem corrected before further use.

BATTERY MAINTENANCE

To protect the battery case from chipping and gouging, do not let the battery sit on a concrete
floor. Install the battery on a shelf or protective pad such as plywood. Always install the battery in
a dry location that is protected from flooding.
Follow the battery manufacturer’s recommendations for maintenance and safe use of the
battery.

«
...
14
15
16
17
18
»

Summary of Contents for 062-3503-8



















Reviews:

No comments