MasterCraft 054-7120-4 Instruction Manual Download Page 24

ANGLE GRINDER - 054-7120-4

23

f)  this warranty will not apply to any product that was sold to the original purchaser as a 

reconditioned or refurbished product (unless otherwise specified in writing); 

g)  this warranty will not apply to any product or part thereof if any part from another manufacturer 

is installed therein or any repairs or alterations have been made or attempted by unauthorized 
persons;

h)  this warranty will not apply to normal deterioration of the exterior finish, such as, but not limited 

to, scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive and chemical 
cleaners; and

i)  this warranty will not apply to component parts sold by and identified as the product of another 

company, which shall be covered under the product manufacturer’s warranty, if any.

Additional limitations

This warranty applies only to the original purchaser and may not be transferred. Neither the retailer 
nor the manufacturer shall be liable for any other expense, loss or damage, including, without 
limitation, any indirect, incidental, consequential or exemplary damages arising in connection with the 
sale, use or inability to use this product.

Notice to consumer

This warranty gives you specific legal rights, and you may have other rights, which may vary from province to 
province. The provisions contained in this warranty are not intended to limit, modify, take away from, disclaim 
or exclude any statutory warranties set forth in any applicable provincial or federal legislation.

IMPORTED BY MASTERCRAFT CANADA TORONTO, CANADA M4S 2B8

W

ARRANTY

Summary of Contents for 054-7120-4

























Reviews: