Dear Customer, thank you for purchasing a MASTER product.
Here you will find important information regarding the methods of use and the safety of installation.
Comply with the following information
and keep for future reference.
FOR A CORRECT INSTALLATION, IT IS RECOMMENDED TO READ THIS INSTRUCTION GUIDE.
The producer cannot be consider responsible for any damages due to improper, wrong or unreasonable use.
WIND DUO is a wind rain safety device for awnings, screens or similars. This device rolls up the awning when
wind and rain speed exceeds the setting threshold. It controls 2 motors with mechanical limit switch.
WARNINGS
1. Technical and general features
(related to 20°C working temperature)
Power Supply :
Contacts capacity :
Dimensions :
Wind threshold :
230 Vac 50/60 Hz
2x10 A@250 Vac
100 x 100 x 60 mm
from 7 to 40 Km/h
01.
02.
03.
.
04.
05.
.
06.
07.
08.
09.
10.
11.
12.
13.
14.
16.
17.
18.
T
.
.
.
Manual controls with high voltage, be careful.
.
.
T
.
he device must be installed by technical qualified staff so as to comply with the laws in force in your locality
Check that the package is intact and it has not suffered damage in transit
This device is subject by dangerous electric voltage.
Always connect the ground wire (yellow/green)
The installer is forced to arrange a section device on the system (with 3 mm minimum opening contacts)
Do not change,open or replace parts without manufacturer’s permission
For your safety, it is forbidden to work close to the roller tube with motor supplied.
In case of malfunctioning do not keep on trying on control and warn the technician.
Operating on the device with caution, using suitable tools.
Check that the power supply line does not depend on circuit for lighting.
he device has not a section part, the technician will take care to provide it into the system.
Be sure that sensor has been installed on the correct position and well exposed to the wind and that there are no obstacles to the blades rotation.
Place rain sensor at about 30/40°slope (see sensor X11 manual).
Strictly adjusting the sensor with blades turned upside
Using sensors produced by the same manufacturer, or the warranty will be cancelled.
The producer cannot be consider responsible for any damages due to improper, wrong or unreasonable use.
Make connections without power supply
Adjust the motor limit switch before connecting it to the device
15.
2. Warnings on installation safety
WIND P DUO
Instruction guide : wind rain control for 2 motors
The device is provided by two manual controls that can be permanent or momentary. Through this controls it is possible to move two awnings, manually or separately. Manual controls will be
disabled in wind alarm condition.
3. Manual control
EXPIRED
At the end of the product cycle, dispose as provide by local regulation, or deliver again to the retailer when purchasing a new one. This product could contain polluting substance for the
environment and dangerous for health, if expired in a wrong way.
WIND P DUO rev.02 dated 30.08.12
Sensor Supported :
Protection Degree :
Protective Fuse
X15C sensor, X11 sensor
Ip55
5x20 fast 6,3 Amp
Working temperature :
from -20°C to +55°C
It closes the awning when the wind or rain speed exceeds the set threshold for longer than 3 seconds.
It exits from wind or rain alarm mode after about 8 minutes . During the wind or rain alarm mode, the manual controls are disabled.
rotating the trimmer on the device. Threshold is adjustable from 7 Km/h (trimmer completed rotate on the left) to 40 Km/h (trimmer completed rotate on the right).
The factory sets up the wind threshold at about 15 Km/h.
When the set wind threshold is exceeded, the red led switches on. If this condition continues for at least 3 seconds, the device enters into wind alarm mode and red led flashes for the whole wind
alarm time.
Once the device connected and wind alarm simulated (bring the awning to middle position and rotate the sensor blades) it can be possible to exit from alarm condition without waiting 8 minutes.
Hold key RESET since led (flashing during the alarm) switches off (about 5 seconds).
How to adjusting wind threshold :
Wind presence signal :
Forced exit from wind alarm mode :
To adjust X11 rain sensor refer to instruction guide of the sensor itself.
4. Wind Rain control
5. Fixing system
connection cables
X
connection cables
X
WRONG FIXING
RIGHT FIXING
R
awning 1
awning 2
awning 1
awning 2
X
WIRED
