Master MP-MBA-45T-1 Installation And Operation Manual Download Page 20

 

 

12 YEAR LIMITED WARRANTY

 

As of  November 2022

 

 

 

 

This  Residential    Water  Conditioner  is  warranted  for  a  period  of 

one  year

  from  date  of 

purchase  by  first  user  against  defects  in  materials  and  workmanship.    In  addition,  the  complete 

control valve is warranted for 

five  years.

  The control valve body (excluding internals and electrical 

parts) is warranted for 

six    years.

  The mineral tank, plastic brine tank or cabinet tank (excluding 

mineral) is warranted against rust, corrosion or bursting for a period of 

twelve  years

 from date of 

manufacture.    Except,  as  specifically  set  forth  in  this  paragraph,  Master  Water  Conditioning 

Corporation makes no other warranties, express or implied.

 

 

 

This warranty shall be void if the conditioner is moved from the place of original installation, 

or if damage is caused by misuse, misapplication, accident, freezing, flood, fire or if not installed in 

accordance with instructions furnished by Master Water Conditioning Corporation.

 

 

 

This  warranty  shall  be  void  in  the  event  of  damages  from  external  sources  or  where  the 

conditioner has been operated at pressure in excess of 100 pounds per square inch or at a temperature 

greater than 100 degrees F. or less than 32 degrees F.   Incidental costs or consequential damages are 

not covered by this warranty.

 

 

 

 All defective parts shall be returned prepaid to Master Water Conditioning Corporation for 

inspection.  

Master shall not be liable for labor charges other than Master factory repairs

.

 

 

 

This warranty gives you specific legal rights, and you may have other rights which vary from 

state to state.  Some states do not allow limitations on duration of implied warranties or exclusion of 

incidental or consequential damages, so the above limitations may not apply to you.

 

 

 

All  claims  must  be  submitted in  writing  to  Master Water  Conditioning  Corporation at  224 

Shoemaker Road, Pottstown, Pennsylvania 19464 within thirty (30) days from the discovery of the 

defect.    Master  Water  Conditioning  Corporation  thereafter  will  correct  defective  parts  and 

workmanship or rusting, corrosion or bursting within sixty (60) days.

 

 

 

 

 

 

 

 

 

 

 

224 Shoemaker Rd. Pottstown, Pa. 19464

 

MASTER

Water Conditioning Corp.

Summary of Contents for MP-MBA-45T-1





















Reviews: