© 2015, Pinnacle Products International, Inc.
8
+9)$LU&LUFXODWRU8VHU¶V0DQXDO
´6+23)$10$&6'')
,QVWDOODWLRQDQG$VVHPEO\
1. Remove Knob Screw (Item #15*) and Wing Nut (Item
#14*) from top of Post.
2. Slide Connector Bracket (Item #4*) onto top of post.
3. Line up holes on the Post and Connector Bracket
(Item #4*).
4. Re-insert the Knob Screw (Item #15) through the Post
and Connector Bracket (Item #14*) and tighten firmly
with the Wing Nut (Item #14*).
5. Place the fan on level ground in a safe, desired position
then connect to an approved power source.
6. Set desired tripod stand height following “Tripod
Operation Instructions” below.
7ULSRG2SHUDWLRQ,QVWUXFWLRQV
75,32'/(*23(5$7,21
1. Fold legs out and slide support bracket to center of leg.
2. To adjust leg height; rotate locking ring clockwise to
loosen.
127(.HHSDILUPJULSRQWKHWULSRGZKLOHOHJLV
XQORFNHG7KHOHJZLOOFROODSVHLQWRLWVHOIXQOHVV
KHOGWLJKWO\
127(%HFHUWDLQWRPDNHDOOWKUHHOHJVWKHVDPH
KHLJKW6HWWLQJOHJVWRGLIIHUHQWKHLJKWVZLOOPDNH
WKHIDQXQEDODQFHGDQG&28/')$//29(5
3. Slide leg extension to desired height.
4. Rotate locking ring counter-clockwise and tighten firmly.
Be sure the leg is secure before moving to next leg.
5. Repeat steps 2-4 for remaining legs.
75,32'&(17(5326723(5$7,21
1. To change the post height; rotate locking ring
counter-clockwise to unlock post.
127(%HFHUWDLQWRNHHSDILUPJULSRQSRVWZKLOH
XQORFNHG7KHIDQZLOOVOLGHGRZQWRLWVORZHVW
SRLQWLILWLVQRWKHOGDQGVORZO\PRYHGWRGHVLUHG
SRVLWLRQ
2. Raise or lower post to desired position.
3. Rotate locking ring clockwise to lock post and tighten
firmly.
DO NOT MOVE OR ADJUST
FAN WHILE IN OPERATION.
THIS CAN CAUSE DAMAGE TO FAN AND
INJURY TO THE OPERATOR.
WARNING
237,21$/&(,/,1*02817
1. Attach Ceiling Mounting Kit (Item #16*) to 2x4” stud
that is able to support 50 lbs continuously using
M6x40mm screw. (See Figure 5**)
3. Be Certain that the Safety Pin lines up with the groove
on the Frame (Item #4). (See Figure 6**)
2. Slide Connector Bracket (Item #4*) onto Ceiling
Mounting Post. (See Figure 7**)
4. Rotate the entire fan so the safety pin locks into place
and the holes on the Mounting Post line up with the
holes on the Connector Bracket (Item #4*). (See Figure
8**)
5. Insert the Base Knob (Item #15*) through the Mounting
Post and Connector Bracket (Item #4*) and tighten
firmly with the Wing Nut (Item #14*).
(See Figure 8**)
* On Page 10
** On Page 9
,QVWDOODWLRQDQG$VVHPEO\
The installer MUST be
certain that the support bracket is
mounted to a minimum of a 2x4”
stud, and that it is able to support 50 pounds
continuously.
WARNING
1(9(5/($9($)$1
81$77(1'(':+,/(
23(5$7,1*25:+,/(
&211(&7('72$32:(5
6285&(
