background image

8

DO NOT DIVE.

105

DO NOT DIVE.

SAFETY INSTRUCTIONS

IMPORTANT SAFETY 

INSTRUCTIONS (CONT.)

 The unit should be subjected to periodic routine maintenance once every quarter to 

make sure that the it is operating properly.

DANGER – Risk of Electric Shock. A green colored terminal or a terminal marked G, 

GR, Ground, Grounding or the symbol shown in Figure 14.1 of UL 1563 is located 

inside the supply terminal box or compartment. To reduce the risk of electric shock, 

this terminal must be connected to the grounding means provided in the electric 

supply service panel with a continuous copper wire equivalent in size to the circuit 

conductors supplying this equipment. 

 At least two lugs marked “Bonding Lugs” are provided on the external surface 

or on the inside of the supply terminal box or compartment. To reduce the risk 

of electric shock, connect the local common bonding grid in the area of the spa 

to these terminals with an insulated or bare copper conductor not smaller than 

8AWG. 

 All field installed metal components such as rails, ladders, drains, or other similar 

hardware within 3m of the spa shall be bonded to the equipment grounding bus 

with copper conductors not smaller than 8AWG. 

SAVE THESE INSTRUCTIONS

Summary of Contents for legacy whirlpool

































































Reviews: