manualshive.com logo in svg

Master Image MI-WAVE3D, Installation & Operation Manual

Share
Download
Master Image MI-WAVE3D Installation & Operation Manual Download Page 7

Installation & Operation Manual | MI-WAVE3D  

 

 

© 

MASTERIMAGE 3D, Inc.

 

7 

 

1. Introduction 

1.1. 

Welcome 

Congratulations on choosing the finest digital projection 3D system available.  

The MASTERIMAGE MI-WAVE3D delivers the clearest full-color images in a cost-
effective and studio-approved single projection, liquid crystal, digital 3D system.   

Paired with MASTERIMAGE high quality 3D eyewear, the MI-WAVE3D provides the 
clearest and truest color 3D picture of any available liquid crystal 3D system. 

This user manual provides all the information required for simple installations and 
the operation of the MI-WAVE3D, with any DLP cinema projector and digital cinema 
server.  

1.2. 

Contacting Technical Support 

If you require technical support, our contact information is listed below:  

 

 

 

 

MASTERIMAGE 3D, INC 

Email:  

 

[email protected]

 

Web Site:  

www.MasterImage3d.com

 

USA Tel:   

+1-323-606-7800

 

UK Tel:    

+44 1753 785131

 

Asia Tel:   

+82-2-3438-1600

 

 

 

 

Summary of Contents for MI-WAVE3D







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands