background image

3

Lowes.com/masterforge

®

        SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate

or install the product. If you have any questions regarding the product, please call

customer service at 1-800-963-0211, 8:00 am to 6:00 pm, EST, Monday- Thursday, 8:00

a.m. to 5:00 p.m., EST, Friday.

• 

The installation of this appliance must conform with local codes or, in the absence of local

codes, with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or Natural Gas

and Propane Installation Code, CSA/CGA-B149.1.

• 

This grill is intended for use outdoors and should not be used in a building, garage or any

other enclosed or covered area.

• 

This outdoor grill is not intended for installation in or on recreational vehicles and/or boats.

• 

A minimum clearance of 36 in. from combustible constructions to the sides of the grill and

36 in. from the back of the grill to combustible constructions must be maintained. This

outdoor cooking gas appliance must not be placed under overhead combustible

construction.

• 

The use of an electrical source requires that when installed, the grill must be electrically

grounded in accordance with local codes or, in the absence of local codes, with

ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1. Keep electrical supply cords

and the fuel supply hose away from heated surfaces.

• 

Inspect the hoses before each use for excessive abrasion or wear, or cuts that may affect

safe operation of the grill. If there is evidence of excessive abrasion or wear, or the hose is

cut, it must be replaced prior to the grill being put into operation. The replacement hose

assembly must be those specified by the manufacturer.

• 

Keep your grill in an area clear and free from combustible materials, gasoline and other

flammable vapors and liquids.

• 

DO NOT obstruct the flow of combustion and ventilation air to this appliance.

• 

Keep the ventilation openings of the tank enclosure free and clear from debris.

• 

Check all gas connections for leaks with a soapy water solution and brush. Never use an

open flame to check for leaks.

• 

Never use charcoal in the grill.

• 

Never use the grill in windy areas.

• 

Only a 20 lb. LP-gas cylinder is allowed. The cylinder must be 

constructed and marked in accordance with the Specifications for

LP Gas Cylinders of the U.S. Department of Transportation (D.O.T.)

or the National Standard of Canada, CAN/CSA-B339, Cylinders,

Spheres and Tubes for Transportation of Dangerous Goods; and

Commission. A 20 lb LP-Gas cylinder’s dimensions are:

• 

Never use the grill without the drip tray installed and pushed completely into the back of

the grill. Without the drip tray, hot grease and debris could leak downward and produce a

fire hazard.

• 

Use only the gas pressure regulator supplied with this appliance. This regulator is set for an 

outlet pressure of 11.0 iwc.

• 

The cylinder used must include a collar to protect the cylinder valve.

8 in.

13.9 in.

12.2 in.

18 in.

Summary of Contents for 503217





















Reviews: