MATCH LIGHTING MAIN BURNERS
MATCH LIGHTING ROTISSERIE BURNER
MATCH LIGHTING SIDE BURNER
If the burner still fails to light after several attempts, try the manual ignition procedure below.
Match lighter
1. Open lid before lighting.
2. Turn the burner control knobs to OFF " ".
3. Slowly open cylinder valve.
4. Place a match in the end of the match lighter. Strike the
match and place to the side of burner.
5. Push and turn the burner control knob anti-clockwise to
approx 1/4 position. The burner should light within 5 seconds.
If the burner does not light, turn the control knob to OFF " " and
wait 5 minutes for accumulated gas vapours to dissipate and repeat
lighting procedure.
For your safety: Do not bend over grill, keep face away when lighting.
1. Open lid before lighting.
2. Turn burner control knobs to OFF " ".
2. Slowly open cylinder valve.
3. Prepare a paper match and place it in the end of the
match lighter. Strike the match and place at burner.
4. Push and turn the rotisserie burner control knob anti-
clockwise to approx 1/4 position. Keep pushing in knob while match
lighting. The burner should light within 5 seconds. When lit, keep pushing on control knob for 30
seconds. Then release it, burner should stay lit.
If the burner does not light, turn the control knob to OFF " " and wait 5 minutes for accumulated gas
vapours to dissipate and repeat lighting procedure.
5. Rotate knob to adjust between 1/4 to 1/2 areas to adjust heat setting.
If burner fails to light after several tries, there could be a problem with the gas source. Turn off gas at
cylinder and all control knobs. DO NOT USE the grill until the problem has been identified and corrected.
For your safety: Do not bend over grill, keep face away when lighting.
1. Open lid before lighting.
2. Turn the burner control knobs to OFF " ".
3. Slowly open cylinder valve.
4. Prepare a paper match in the end of the match lighter. Strike the match
and through the cooking grid place to the side of a selected burner.
5. Push and turn the selected burner control knob anti-clockwise to
approx 1/4 position. Keep pushing the control knob. The burner should light
within 5 seconds. When lit, release knob and turn between 1/4 to 1/2 areas to
adjust heat setting. If the burner does not light, turn the control knob to OFF " "
and wait 5 minutes for accumulated gas vapours to dissipate. Then, repeat lighting procedure.
6. Once lit, light adjacent burners in sequence by pressing in and rotating the
control knob anti-clockwise to approx 1/4 position. Release then turn
between 1/4 to 1/2 areas to adjust heat setting. If burner fails to light after several
tries, there could be a problem with the gas source. Turn off gas at cylinder and all
control knobs.DO NOT USE the grill until the problem has been identified and corrected.
23
Summary of Contents for SRGG41126
