background image

Master Audio 

Xcellence Series.Ver 1.1 

 

Nov 09 

3

1. INTRODUCTION 
 
1.1. General product information 
 
Master Audio

 thank you for the trust placed in our 

Xcellence

 loudspeaker system. 

 
The Xcellence series combines the benefits of its coaxial point sound sources, the 
convenience of a self-powered system and the flexibility of the DSP (digital system 
processing) for cabinet control. 
 
More than 35 years’ experience in amplifier and acoustic cabinet design using the 
highest technology and components come together to give you a product ideal for a 
multitude of applications, from sound back-up systems for theatres, clubs or TV 
channels to even churches, corporative events or concert halls. 
 
Coaxial technology achieves a sound distribution system which is totally coherent and 
in phase (as a point source). This is due to the fact that the directivity of the high and 
low frequency transducers couples up perfectly with the crossover frequency from the 
filters. This results in very smooth transitions between the bass and high frequency 
zone and the elimination of secondary null zones due to polar lobbing, typical of 
those systems using separate woofer and horn. 

 

The directivity of the cabinets with coaxial transducers is totally symmetric in the 
horizontal or vertical plane.  
 
We suggest you read the following information with attention, assured that it will be of 
maximum use in helping you to achieve the best results and optimum performance.  

 
1.2. Features and appearance 
 

X-12C & X-15C 

 

- Self-powered 

cabinet. 

-  750W amplifier for mid range. 
-  250W amplifier for high range. 
-  DSP with 48 bit bus and 28 bit filter coefficients. 
-  DSP Controls (parametrics, delay, volume and limiters). 
-  RJ45 output for control via computer. 
-  Overvoltage protection (>250V-400V). 
-  2 way coaxial speaker with 80º symmetry, including one 12” / 15” woofer in 

neodymium and one 3” voice coil diameter, titanium diaphragm compression 
driver. 

-  Birch plywood construction. 
-  Varnished finish. Optional black textured paint finish: totally ecological.  
-  Frontal steel grille with acoustically transparent grey cloth. 

 

 

 
 
 
 

 

Summary of Contents for X-18W























Reviews: