background image

Master Audio 

CS Series. Version 1.0  

 

 Mar14 

11

possibility of damage or wear out during transport.  For devolution of a defective new 
product, it should be sent back in its original packaging with all its accessories and internal 
protection elements.  Amate Electroacústica,s.l. reserves the right of not admitting any 
devolution or damaged material sent back if the packaging is in bad conditions. 
 
Once received the material, the Authorized Technical Service will make an evaluation of the 
damages and determine the cost of repair or proceed to apply the warranty or replacement 
of the product if proceeds. 
 

Warranty Rights

The product indicated in the purchase invoice is for PROFESSIONAL use, and it is 
protected under the law 23/2003 of July 10th about Warranties in the Sale of Consumer 
Goods.  Notwithstanding, Amate Electroacústica,s.l. voluntarily grants WARRANTY over 
possible defects in manufacturing for the above mentioned period for each Series or group 
of products. 
 

Conditions

:  

The buyer has been informed about the maintenance required for the 

material purchased in order to keep it in perfect

 

conditions

 

 

of use and maintenance, as well as to avoid its wear out.  The buyer has also received 
(corresponding to each case) one Manual with the technical features of the product purchased and 
the instructions for its correct use. 

 
The buyer, after checking the purchased material, accepts the reception of the product 
without any type of external damage, in good conditions of use, without prejudice of 
possible nonconformity that could happen as a consequence of its use. 

 

Validity periods

:  The warranty is effective from the date of purchase of the product, 

being valid against the presentation of the corresponding invoice, provided that it shows 
the original serial numbers of the manufacturer matching to the serial numbers shown in 
the identification labels stuck on every product.  Any product that does not have the 
corresponding serial number could be excluded of any warranty right by unilateral 
decision of our Commercial Department.   
 

Warranty for products repaired by Amate Electroacústica,s.l

Any product or part replaced by the Technical Service of Amate Electroacústica, s.l. has a 

90-day

 warranty from the date of the repair (with the paid invoice), provided that the same 

failure is produced by the same reasons and is not related to any misuse or mistreat. 
 
In any case of technical assistance given by Amate Electroacústica,s.l or any of its 
Authorized Technical Services, the client cannot demand any compensation for indirect 
damages arisen from professional services to third parties, as well as the loss of benefits 
or incomes caused by the product breakdown. 

 

Summary of Contents for CS6/T






















Reviews: