Mastech MS20006 User Manual Download Page 7

12

13

Polarity indication 

“-”displayed for negative 
polarity

Overrange Indication 

Only figure “1” on the display

Jaw opening capability 

55mm (Max conductor size)

Power 

9V battery, NEDA 1604 or 
IEC 6F22 

Low battery indication 

“      ” appears on the display

Operating Environment  

0 to 40°C

Storage temperature 

-10°C to 50°C

Temperature coefficient 

0.1×specified accuracy) /
 °C ( <18°C or >28°C )

Altitude 

 2000m

Size 

282mm×104mm×47mm 

Weight 

Approx.570g.

DC VOLTAGE

Range 

2V

20V

200V

1000V

Resolution 

1mV

10mV

0.1V

1V

Accuracy 

±0.5% of rdg ± 1 digit 

±1.0% of rdg ± 2 digit 

Input Impedance: 10M

Ω

AC VOLTAGE

Range 

200V

750V

Resolution 

0.1V

1V

Accuracy 

±1.0% of rdg ± 3 digit 

Input Impedance: 10M

Ω

Frequency range: 40Hz to 400Hz. 
Response: Average responding, calibrated in rms. of sine 

wave.

AC CURRENT

Range 

200A

2000A

Resolution 

0.1A

1A

Accuracy 

±2.0% of rdg ± 5 digit 

Overload Protection: 2200A for 60 seconds maximum.
Frequency range: 50Hz to 60Hz.

<600A  ±2.0% of rdg ± 5 digits
600A to1000A  ±3.0% of rdg ± 5 digits
>1000A  ±3.0% of rdg ± 15 digits
 

RESISTANCE

Range 

200

Ω

20k

Ω

Resolution 

0.1

Ω

10

Ω

Accuracy 

±1.0% of rdg ± 3 digit 

2M

Ω

1k

Ω

±1.5% of rdg ± 15 digit 

±1.5% of rdg ± 15 digit 

Summary of Contents for MS20006









Reviews: