MASSEY FERGUSON 8650 Manual Download Page 13

Page: 13 / 15

192

8600 - EAME

4315972M4 - 2

4. Maintenance

Crop_this_page

4.4

Transmission

4.4.1

Recommended products

T001563

MPORTANT

The warranty remains valid only as long as the lubricants used comply with the following clas-

sifications, and no other products are used.

Transmission

SAE 15W40 oil complying with MF specifications CMS M1145.

Hydraulic clutch.

Pentosin CHS 11S oil.

Rear final drives

Models 8650/8660: SAE 85W90
Models 8670/8680/8690: SAE 85W140

4.4.2

Checking the transmission oil level

T001409

Frequency

Check the transmission oil level every day.

Procedure

1. Stand the tractor on level ground, with the front

axle suspension disengaged.
Stop the engine

2. Check that the level is between the minimum

and maximum marks on the dipstick .

3. Top up if necessary.

4.4.3

Draining the transmission oil

T001411

Frequency

Drain and replace the transmission oil every 2000 hours.

I004133

Fig. 1.

Maxi

Mini

Summary of Contents for 8650
















Search results

Summary of Contents for 8650

Reviews:

Related manuals for 8650

Brands by name

Popular brands

MASSEY FERGUSON 8650, Manual

Search results

Summary of Contents for 8650

Reviews:

Related manuals for 8650

Brands by name

Popular brands