1.12.2
ACC and RMT Models
These have the fan assembly mounted inside the pedestal rear panel. A thermodisc switch is fitted
adjacent to the rear of the firebox.
1.
Un-plug the lead from the mains supply.
2.
Remove the four retaining screws at the rear of the pedestal.
3.
Lift the fan assembly carefully away from the pedestal until the loom connector block is exposed.
4.
Disconnect the connector block and lift the fan clear.
5.
Reverse the extraction procedure when re-assembling.
1.12.3
Aust. STD Models
These have the fan assembly mounted on the rear of the heater cabinet. The mains cord enters the fan
assembly and an internal loom extends up to the three speed switch at the top control panel. No
thermodisc switch is fitted.
1.
Un-plug the lead from the mains supply.
2.
If fixing screws are fitted along the top of the fan housing, remove them.
3.
While supporting the housing from falling outward, lift it up to disengage it from the keyhole slots.
4.
Carefully swing the top of the fan housing away from the heater cabinet until it can be lifted clear of the
cabinet at its bottom edge which sits in a ‘V’ formation on the opening in the cabinet.
5.
Swing the right end (viewed from the rear) of the fan housing away from the heater and move the
housing a little to the right to expose the plug and socket in the fan loom.
6.
Disconnect the plug and socket and lift the fan clear.
7.
Reverse the extraction procedure when re-assembling.
1.12.4
ECS Models - Aust. and N.Z.
These have the fan assembly mounted on the rear of the heater cabinet. The mains supply is delivered
through the ECS control box which is mounted inside the rear pedestal panel. Speed control is provided
by a signal from the handpiece to the receiver which is processed by the ECS control box. A thermodisc
switch is fitted adjacent to the rear of the firebox.
To extract and replace the fan assembly, follow steps 1 – 7 in 1.12.3
1.13 REMOVING AND REPLACING THE PEDESTAL
1.
Remove the fan (see Section 1.11) or pedestal rear panel as applicable.
2.
Remove the front panel, dress guard (if fitted), louvre assembly and glass . See Section 1.1.
3.
Remove the logs carefully.
4.
Disconnect the thermostat bulb if attached to the pedestal.
5.
Remove the four screws retaining the pedestal to the baseplate.
6.
Lift the firebox clear. Note: The heat shield below the baseplate will still be partially attached.
7.
Reverse the removal sequence when re-assembling the pedestal.
1.14 REMOVING AND REPLACING THE PEDESTAL FOOT
1.
First carefully disconnect the receiver loom at the plug near the receiver control box (RMT models) or at
the plug on the rear pedestal panel (ECS models).
2.
To remove the foot, carefully slide the foot and trim forward, keeping it in contact with the floor to
avoid damaging the finish on the pedestal.
3.
To replace the foot, make sure the decorative trim is correctly in place before sliding the foot and trim
back around the pedestal, again keeping the foot in contact with the floor to avoid pedestal finish
damage.
4.
Re-connect the receiver loom (if applicable).
1.15 ACCESSING THE THERMODISC
(Recent Baltimores & Monacos except Aust. STD)
If the heater has a fan mounted on the rear of the cabinet, remove the fan (see 1.12) to reach the
thermodisc. If easier access is needed, also remove the rear access panel.
For other models, remove the rear access panel to access the thermodisc.
15
Summary of Contents for BALTIMORE MONACO NAPLES
