Masotti X100M User Manual Download Page 8

X100M1.1ENG

 

 

X

100M User manual      

8/13

 

 

MIDI pedalboard phantom power supply (optional). 

MIDI pedalboard can be supplied directly by X100M through a MIDI 5 or 7 poles cable. Its' 
recommended to check the correct polarity of your pedalboard before connecting. This 
function is a free of charge optional and it must be set on factory. Please, contact MGD 
before delivery for correct wiring of the connector. 

 

Startup sound setups. 

X100M is a head engineered  to give the widest flexibility of the sound.  We developed  
circuital solution completely different from usual, so a period of training ( specially on eq 
knobs) is necessary to reach the best results. In this section we report some start-point 
setups. Furthermore, we have developed two hardware setups, based on different final 
tubes: 
 

X100M Classic

: four  selected E34L, a new interpretation of the british  sound, with a 

proud and aggressive soul, at  the same time round and elegant. Dedicated to vintage 
sound lovers.  
 

X100M Modern

: 4 X E34L or 4 X 6L6, two deeply different versions: strong and 

heavy the first,  round and elegant the second. For players who need a modern, versatile, 
ultra-dynamic and ultra-defined amplifier. 
 

A brief channel description 
 
Clean

: dedicated to clean sound, it's equipped with a brite switch to refresh high 

frequencies. Drive and volume controls are inter-dependt and they can be set in order to 
obtain different sounds: drive high and volume low for a "full and strong" sound,  drive low 
and volume high for "crystal brilliance" results. At high levels and with an external booster, 
it's easy to have a very impressive crunch. 

 

Crunch

: channel for mean overdriven sounds, available in two versions: Crunch and 

Boosted Crunch. Crunch starts from  clean gradually dirty up to reach a rhythm rock sound 
full and dynamic.  Acting on the guitar volume, it's possible to have a wide variety of 
degrees of crunch. Boosted crunch is similar to the former but is more useful for modern 
sounds, both for rhythm and solo parts, with very high gain, dynamics and transparency. 
 

Lead

: modern high gain channel,  great headroom with rich armonics, perfect for solo 

parts. Very reactive to the pick, with a solid and fully controlled response to low 
frequencies, it gives a "liquid" and sustained sound.   
 
Here you have some basic setup: 

 
 
 
 
 

Funky 

 
 
 

treble 

middle 

bass volume 

drive 

CLEAN 

brite 

Summary of Contents for X100M














Reviews: