background image

 

2

not be used until the fault is rectified. 

1.  Thoroughly inspect the compactor for signs of 

damage. Check components are present and secure. 

Pay special attention to the belt drive safety guard 

fitted between the engine and the vibrator unit. 

2.  Check the engine oil level and top up as necessary. 

3.  Check the engine fuel level and top up as necessary. 

4.  Check for fuel and oil leaks 

 

Start and stop Procedure for Engines 

 
Diesel Engine 
 

1. 

Open the fuel cock. 

 

 

 

 

 

 

 

 

 

 

 

2.  Turn the governor lever to “START” position. 

3.  Hold the recoil starter handle. 

4.  Pull the starter handle until you feel the resistance, 

then return handle slowly. 

5.  Press the decompression lever to “Non-compression” 

position. The lever will return back automatically after 

the engine started. 

 

 

 

 

 

 

 

 

6.  Hold the recoil starter handle with two hands and pull 

it hardly. 

7.  It is difficult to start the engine at cold weather. 

Remove the rubber plug on the cylinder head and fill 

about 2CC engine oil before starting. 

8.  To stop the engine, set the governor lever to the low 

speed position, then run the engine at zero load five 

minutes. 

9.  Set the governor lever to the “STOP” position. Do not 

stop the engine with the decompression lever. 

10. 

Set the fuel cock the “OFF” position. 

! FIRE & EXPLOSION HAZARDS 

PETROL is extremely flammable and explosive under certain

conditions. 

 

ENSURE that the petrol is only stored in an approved storage

container. 

 

DO NOT refuel the motor while it is in operation or hot. 

 

DO NOT refuel the motor in the vicinity of sparks, a naked flame or

a person smoking. 

 

DO NOT over fill the fuel tank and avoid spilling petrol when

refueling. Spilled petrol or petrol vapour may ignite. If spillage

occurs, ensure that the area is dry before starting the motor. 

 
ENSURE that the fuel tank cap is securely fitted after refueling. 
 

! CHEMICAL HAZARDS 

 

DO NOT operate or refuel a petrol or diesel motor in a confined

area without adequate ventilation. 

 

CARBON MONOXIDE exhaust gases from internal combustion

motor driven units can cause death in confined spaces. 

 

! NOISE HAZARDS 

 

EXCESSIVE NOISE can lead to temporary or permanent loss of

hearing. 

 

WEAR an approved hearing protection device to limit noise

exposure. As required by Occupational Health and Safety

regulations. 

 

PROTECTIVE CLOTHING   

 

ALWAYS wear approved hearing protection when working in a

confined work space. Protective goggles and a dust mask should

be worn when working in a dusty environment. Protective clothing

and footwear may also be desirable when working with hot mix

bitumen. 

 

! ADDITIONAL HAZARDS 

 

Slip/Trip/Fall is a major cause of serious injury or death. Beware of

uneven or slippery work surfaces. 

 

Exercise care when working in the vicinity of unprotected holes or

excavations. 

 

OPERATION 

 

Pre start-up inspection 

 

The following Pre-start-up inspection must be performed before

the start of each work session or after every four hours of use,

whichever is first. If any fault is discovered, the compactor must 

decompression lever

fuel cock 

regulator 

handle 

Summary of Contents for MSH160





















Reviews: