MANUAL TRANSMISSION 5B-31
Fifth Gear
1) To seat countershaft L bearing cup (2) to bearing cone, tap cup
by using special tool and plastic hammer.
Special Tool
(A): 09913M84510
2) Put a shim on bearing cup provisionally, place straight edge
over it and compress it by hand through straight edge, and then
measure “a” (Clearance between case surface and straight
edge) by using feeler gauge.
Clearance “a”: 0.08 – 0.12 mm (0.0032 – 0.0047 in.)
(Shim protrusion)
3) By repeating above step, select a suitable shim which adjusts
clearance “a” to specification and put it on bearing cup.
Note:
Insert 0.1 mm (0.004 in.) feeler to know whether or not a
shim fulfills specification quickly.
0.40, 0.45, 0.50, 0.55, 0.6, 0.65,
0.7, 0.75, 0.8, 0.85, 0.9, 0.95, 1.0,
1.05, 1.1 and 1.15 mm
Available shim
(0.015, 0.017, 0.019, 0.021,
thickness
0.023, 0.025, 0.027, 0.029,
0.031, 0.033, 0.035, 0.037,
0.039, 0.041, 0.043 and
0.045 in.)
4) Place left case plate (1) inserting its end in groove of shift guide
shaft (2) and then tighten it with new 6 screws (3).
Note:
•••••
Be sure to use new screws.
•••••
After tightening screws, make sure that counter shaft
(4) can be rotated by hand feeling some load.
Tightening Torque
(a): 9 N.m (0.9 kg-m, 6.5 lb-ft)
Summary of Contents for Zen Estilo 2018
